Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Brake/EPB / Data List.


g.

According to the display on the GTS, read the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
IG1 Voltage Value IG1 terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V*4
Ignition switch ON: 10.5 to 16.0 V*5
Changes in proportion to auxiliary battery voltage
BS1 Voltage Value +BS terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


Motor Power Supply Voltage BM terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal BM (which supplies power to the ABS motor) of the skid control ECU (brake actuator assembly)


FR Wheel Speed Front speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


FL Wheel Acceleration Front wheel LH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


RR Wheel Acceleration Rear wheel RH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


RL Wheel Acceleration Rear wheel LH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Zero Point of M/C Memorized zero value Min.: -12.5 MPa
Max.: 12.4 MPa
- -
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C
Max.: 175°C
Displays temperature master cylinder pressure sensor -
M/C Sensor Grade Master cylinder pressure sensor change (value detected by ECU) Min.: -30 MPa/s
Max.: 225 MPa/s
Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Zero Point of Decele2 Memorized zero value Min.: -25.105 m/s2
Max.: 24.908 m/s2
- -
Zero Point of Decele Memorized zero value Min.: -25.105 m/s2
Max.: 24.908 m/s2
- -
Yaw Rate Sensor Value Yaw rate sensor (airbag sensor assembly) Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Sensor Memorized zero value Min.: -128°/s
Max.: 127°/s
After completing zero point calibration: 0° -
Zero Point of Yaw Rate Sensor2 Memorized zero value Min.: -128°/s
Max.: 127°/s
After completing zero point calibration: 0° -
Steering Angle Value Steering angle sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0°
-
Zero Point of Steering Angle Memorized zero value Min.: -3276.8°
Max.: 3276.7°
- -
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to the ABS motor) from the skid control ECU (brake actuator assembly) to the ABS motor relay


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake actuator assembly) to the ABS solenoid relay


Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%
Max.: 127.5%
Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Power Train Driving force Powertrain drive torque Min.: -327680 N
Max.: 327670 N
- -
Gear Position Gear position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R Actual gear position -
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position -
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Brake Hold Control Mode Brake hold control mode Out of control mode /
Pressure hold mode /
Pressure release mode /
EPB lock mode
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated)
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated)
EPB lock mode: Parking brake is engaged during brake hold control
HINT:
·

EPB stands for electric parking brake

·

If the brake pedal is not depressed for 3 minutes or more after entering pressure hold mode, the system automatically changes to EPB lock mode



FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
Vehicle Speed Grade Vehicle acceleration Min.: -25.105 m/s2
Max.: 24.908 m/s2
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During driving: Changes in proportion with vehicle acceleration/deceleration
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Travel Distance from IG ON Driving time after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Elapsed Time Time elapsed after ignition switch turned to ON Min.: 0.00 s
Max.: 100661.760 s
- -
MT2 Motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
- -
IG Switch Ignition switch ON status OFF / ON - -
Downhill Assist Control SW Downhill assist control switch OFF / ON - for AWD
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Parking Brake SW Parking brake switch OFF / ON OFF: Parking brake released
ON: Parking brake applied
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake pedal support assembly) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Brake Hold Switch Brake hold switch (electric parking brake switch assembly) (PKB terminal input) OFF / ON OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON
HINT:

The brake hold switch (electric parking brake switch assembly) state is determined using the voltage at terminal PKB


Stop Light Relay Stop light control relay (stop light switch assembly) status
(STP terminal input)
OFF / ON OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed
HINT:

The voltage of power supplied to the stop lights is measured at the STP terminal.


Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
HINT:

Refer to utility for details on how to enter Inspection Mode*1


TRC(TRAC) Control TRC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
HAB Control High power assist brake status OFF / ON OFF: During not control
ON: During control
-
Fail Status Brake booster failure status OFF / ON OFF: During not control
ON: During control
-
Fail Control Failure control status OFF / ON OFF: During not control
ON: During control
-
BA Ctrl Status BA control status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
w/ Pre-collision System
Stop Light Relay State for ECU Control Stop light control relay (stop light switch assembly) status (STPO terminal output) (for ECU control) OFF / ON OFF: Stop light control relay (stop light switch assembly) off (stop light off)
ON: Stop light control relay (stop light switch assembly) on (stop light on)
-
Engine Stop by Stop and Start System Engine stopped by stop and start system status (for ECU control) OFF / ON OFF: Engine not stopped by stop and start control
ON: Engine stopped by stop and start control
w/ Stop and Start System
Solenoid State for ECU Control ABS solenoid relay status (for ECU control) OFF / ON OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating
-
Motor State for ECU Control ABS motor relay status (for ECU control) OFF / ON OFF: ABS motor relay not operating
ON: ABS motor relay operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion OFF / ON OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
-
Buzzer Meter buzzer OFF / ON OFF: Buzzer off
ON: Buzzer on
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

For details on Dealer Mode (Signal Check), refer to test mode procedure*2

·

For details on Dealer Mode (Calibration), refer to utility*3



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 35 km/h (22 mph) or more for approximately 1 second


TRC(TRAC)/VSC OFF SW VSC OFF switch (CSW terminal input) OFF / ON OFF: VSC OFF switch OFF
ON: VSC OFF switch ON
HINT:

The VSC OFF switch state is determined using the voltage at terminal CSW


Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
FR Speed Signal Status Front wheel RH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
FL Speed Signal Status Front wheel LH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
RR Speed Signal Status Rear wheel RH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
RL Speed Signal Status Rear wheel LH speed signal status Normal / Fixed Normal: Wheel speed signal not stuck
Fixed: Wheel speed signal stuck
-
ABS Solenoid (SRLR) Rear pressure reduction solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRLH) Rear pressure holding solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRR) Rear pressure reduction solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRH) Rear pressure holding solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLR) Front pressure reduction solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLH) Front pressure holding solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRR) Front pressure reduction solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRH) Front pressure holding solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


TRC(TRAC)/VSC Solenoid (SM2) Master cylinder cut solenoid (Brake Pressure Control Solenoid "B") status OFF / ON OFF: Not operating
ON: Operating (pressure regulation)
HINT:

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor


TRC(TRAC)/VSC Solenoid (SM1) Master cylinder cut solenoid (Brake Pressure Control Solenoid "A") status OFF / ON OFF: Not operating
ON: Operating (pressure regulation)
HINT:

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor


ABS Motor Relay Motor relay OFF / ON OFF: Motor relay off
ON: Motor relay on
-
Solenoid Relay Solenoid relay OFF / ON OFF: Solenoid relay off
ON: Solenoid relay on
-
STPO Stop light control relay (stop light switch assembly) status (STPO terminal output) OFF / ON OFF: Stop light control relay (stop light switch assembly) off (Stop light off)
ON: Stop light control relay (stop light switch assembly) on (Stop light on)
HINT:

When STPO is ON, the Stop light control relay (stop light switch assembly) turns ON and the stop lights illuminate





CHECK FOR INTERMITTENT PROBLEMS


HINT:

A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected using the Data List function of the GTS.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Follow the directions on the GTS to display the Data List and select areas where momentary interruption should be monitored.

HINT:
·

A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).

·

If Under intermittent remains displayed for one of the items on the GTS, check for continuity between the ECU and the item for which Under intermittent is displayed.

·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.



Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
FL Speed Open Front speed sensor LH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RR Speed Open Rear speed sensor RH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RL Speed Open Rear speed sensor LH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
EFI Communication Open ECM communication open detection Normal / Under intermittent Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected
-
Yaw Rate Open Yaw rate sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Deceleration Open Acceleration sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Steering Open Steering angle sensor open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Master Cylinder Open Master cylinder pressure sensor open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Normal / Under intermittent Normal: Noise not detected
Under intermittent: Noise detected
-
Brake Pedal Switch Open Brake pedal load sensing switch (brake pedal support assembly) open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Yaw Rate Sensor Voltage Open Yaw rate sensor (airbag sensor assembly) voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
EFI Communication Invalid ECM communication invalid detection Normal / Under intermittent Normal: ECM communication invalid state not detected
Under intermittent: ECM communication invalid state detected
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Solenoid Power Supply Open Solenoid power supply voltage status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Motor Power Supply Open Motor power supply voltage status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Stop Switch Open Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Stop and Start ECU Communication Open Engine stop and start ECU communication open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
w/ Stop and Start System
Air Bag ECU Communication Open Airbag sensor assembly open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-

f.

Select the line graph display.


g.

Using the line graph, check whether the status is "Normal" or "Under intermittent".

OK:

Normal is displayed.


HINT:

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.



h.

While observing the screen, gently jiggle the connector or wire harness between the ECU and each sensors, or between ECUs.

OK:

Normal is displayed.


HINT:
·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.

C399553E26
0.073,0.073 5.26,0.531 5.188,0.458 10 false Reference: GTS display at momentary interruption 0.208,0.875 1.823,1.292 1.615,0.417 10 false Wire Harness condition 0.948,1.927 1.792,2.26 0.844,0.333 10 false Line Graph 2.615,1.406 3.406,1.604 0.792,0.198 10 false 1 second 4.24,1.417 5.177,1.635 0.938,0.219 10 false 2 seconds 4.083,0.375 5.385,0.688 1.302,0.313 10 false 1.5 seconds 2.427,0.354 3.458,0.552 1.031,0.198 10 false 0.5 seconds 5.656,1.76 6.927,2.073 1.271,0.313 10 false Under intermittent 5.667,2.135 6.417,2.469 0.75,0.333 10 false Normal 5.625,0.708 7.104,1 1.479,0.292 10 false Momentary interruption 5.635,1.073 6.385,1.396 0.75,0.323 10 false Normal

·

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.





ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Brake/EPB / Active Test.


g.

According to the display on the GTS, perform the Active Test.

NOTICE:
·

Although the Active Test automatically turns off the pump motor after approximately 5 seconds in order to protect the motor, do not operate the pump motor repeatedly without sufficient waiting time in between.

·

Although the Active Test automatically turns off each solenoid after approximately 2 seconds in order to protect the solenoid, do not operate the solenoids repeatedly without sufficient waiting time in between.

·

Do not depress the brake pedal when only the pressure release solenoids valves are ON.



Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
EBS Relay Emergency brake signal operation Relay Start Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Whether the hazard warning lights blink when the EBS Relay is on can be confirmed.
ABS Solenoid Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR)
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


for LHD: Refer to on-vehicle inspection for the brake actuator*1
for RHD: Refer to on-vehicle inspection for the brake actuator*2
VSC Solenoid Master cylinder cut solenoid (SMF (SM1), SMR (SM2)) Solenoid Start (Activate)
Solenoid SMF / SMR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


Check that the GTS display for the solenoid (SM1 or SM2) changes to ON/OFF during Solenoid Start (Activate)
Motor Relay ABS motor relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


for LHD: Refer to on-vehicle inspection for the brake actuator*1
for RHD: Refer to on-vehicle inspection for the brake actuator*2
Solenoid Relay Solenoid relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Perform the Active Test and check that the voltage displayed for the solenoid power supply voltage Data List item changes.
Stop Lamp Relay Stop light control relay (Stop light switch assembly) OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON