Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  Zero Point Calibration of Steering Angle Sensor Malfunction (X20D7)  


DESCRIPTION

Code Tester Display Measurement Item Trouble Area
X20D7 Zero Point Calibration of Steering Angle Sensor Malfunction History of the steering angle sensor zero point calibration position differing from the stored value
·

Poor adjustment of the center position of the steering wheel

·

Poor adjustment of wheel alignment



CAUTION / NOTICE / HINT

NOTICE:

After performing the inspection, check and clear the vehicle control history (RoB).


PROCEDURE

1.CHECK DTC (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CLEAR VEHICLE CONTROL HISTORY (RoB)

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.CLEAR VEHICLE CONTROL HISTORY (RoB)
a.

Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55

Result:
Proceed to
NEXT



NEXT

3.CLEAR ZERO POINT VALUE FOR YAW RATE AND ACCELERATION SENSOR
3.CLEAR ZERO POINT VALUE FOR YAW RATE AND ACCELERATION SENSOR
a.

Clear the zero point value for the yaw rate and acceleration sensor.

Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560

Result:
Proceed to
NEXT



NEXT

4.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
4.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

5.CHECK ZERO POINT CALIBRATION OF STEERING ANGLE SENSOR
5.CHECK ZERO POINT CALIBRATION OF STEERING ANGLE SENSOR
a.

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.


b.

Drive the vehicle at 15 km/h (9 mph) or more for at least 60 seconds.


c.

Check that the centered position of the steering wheel is correctly set while driving straight ahead.

OK:

The steering wheel is centered correctly.



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING SYSTEM

NG

8.ADJUST WHEEL ALIGNMENT
6.INSPECT STEERING SYSTEM

Click hereSteering>STEERING COLUMN>STEERING SYSTEM>ON-VEHICLE INSPECTION

OK:

Normal.


Result:
Proceed to
OK
NG



OK

NG

7.REPAIR OR REPLACE MALFUNCTIONING PART
7.REPAIR OR REPLACE MALFUNCTIONING PART
Result:
Proceed to
NEXT



NEXT

9.CLEAR VEHICLE CONTROL HISTORY (RoB)
8.ADJUST WHEEL ALIGNMENT

Result:
Proceed to
NEXT



NEXT

9.CLEAR VEHICLE CONTROL HISTORY (RoB)
9.CLEAR VEHICLE CONTROL HISTORY (RoB)
a.

Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55

Result:
Proceed to
NEXT



NEXT

10.CLEAR ZERO POINT VALUE FOR YAW RATE AND ACCELERATION SENSOR
10.CLEAR ZERO POINT VALUE FOR YAW RATE AND ACCELERATION SENSOR
a.

Clear the zero point value for the yaw rate and acceleration sensor.

Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560

Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
11.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

12.PERFORM ZERO POINT CALIBRATION OF STEERING ANGLE SENSOR
12.PERFORM ZERO POINT CALIBRATION OF STEERING ANGLE SENSOR
a.

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.


b.

Drive the vehicle at 15 km/h (9 mph) or more for at least 60 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK VEHICLE CONTROL HISTORY (RoB)
13.CHECK VEHICLE CONTROL HISTORY (RoB)
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Using the GTS, check for Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55

Result:
Result Proceed to
Vehicle Control History (RoB) is not output. A
Vehicle Control History (RoB) is output. B



A

END

B