Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420117 SEAT HEATER SYSTEM C

SEAT  SEAT HEATER SYSTEM  B14B5  Lost Communication with Front Seat Temperature Adjustment Switch LIN  


DESCRIPTION

The front seat heater switch (air conditioning control assembly) communicates with the air conditioning amplifier assembly via LIN communication.

If the LIN communication system is malfunctioning, the air conditioning amplifier assembly will not operate even if the front seat heater switch (air conditioning control assembly) is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area
B14B5 Lost Communication with Front Seat Temperature Adjustment Switch LIN Lost communication with the front seat heater switch (air conditioning control assembly)
·

Front seat heater switch (Air conditioning control assembly)

·

Air conditioning amplifier assembly

·

Wire harness or connector

·

ECU-IG1 NO. 4 fuse



WIRING DIAGRAM

B570059E02
1.167,0.969 1.781,1.167 0.615,0.198 10 false LIN1 2.792,0.969 3.469,1.323 0.677,0.354 10 false LIN1 1.552,0.802 2.167,1 0.615,0.198 10 false 7 2.188,0.802 2.802,1 0.615,0.198 10 false 3*1, 8*2 0.26,1.844 0.875,2.042 0.615,0.198 10 false H62 0.26,2.01 1.823,2.552 1.563,0.542 10 false Air Conditioning Amplifier Assembly 2.74,1.854 3.354,2.052 0.615,0.198 10 false H27 2.74,2.031 5.333,2.427 2.594,0.396 10 false Front Seat Heater Switch (Air Conditioning Control Assembly) 4,1.24 4.615,1.438 0.615,0.198 10 false 8*1, 10*2 3.656,0.573 4.271,0.771 0.615,0.198 10 false IG+ 4,0.458 4.615,0.656 0.615,0.198 10 false 4*1, 6*2 4.448,0.74 5.448,1.01 1,0.271 10 false ECU-IG1 NO. 4 5.594,0.573 7.094,0.844 1.5,0.271 10 false from IG1-NO. 1 Relay*3 0.875,3.219 2.656,3.5 1.781,0.281 10 false : LIN Communication Line 3.583,1.385 4.198,1.583 0.615,0.198 10 false GND 3,2.823 4.677,3.115 1.677,0.292 10 false *1: for 12.3 Inch Display 5.135,2.823 6.813,3.115 1.677,0.292 10 false *2: for 8 Inch Display 5.594,0.958 6.938,1.354 1.344,0.396 10 false from Engine Stop and Start ECU*4 3,3.219 4.906,3.594 1.906,0.375 10 false *3: w/o Stop and Start System 5.135,3.219 7.063,3.51 1.927,0.292 10 false *4: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B14B5 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) - GROUND)
3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) - GROUND)
a.
B569381C04
1.5,0.26 1.896,0.51 0.396,0.25 2.375,0.677 1.917,1.125 true 1.365,1.844 1.667,1.448 true 1.302,1.406 1,1.406 true 2.313,1.792 2.094,1.448 true 1.583,0.302 2.063,0.625 0.479,0.323 10 false H27 2.438,0.604 3.021,0.875 0.583,0.271 10 false IG+ (*A) 1.104,1.885 1.75,2.115 0.646,0.229 10 false GND (*A) 0.458,1.313 1.042,1.583 0.583,0.271 10 false IG+ (*B) 2.375,1.802 2.948,2.021 0.573,0.219 10 false GND (*B) 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a
*A for 12.3 Inch Display
*B for 8 Inch Display
*a Front view of wire harness connector
(to Front Seat Heater Switch (Air Conditioning Control Assembly))


Disconnect the H27 front seat heater switch (air conditioning control assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
for 12.3 Inch Display
Tester Connection Condition Specified Condition
H27-4 (IG+) - Body ground Ignition switch ON 11 to 14 V
H27-4 (IG+) - Body ground Ignition switch off Below 1 V

for 8 Inch Display
Tester Connection Condition Specified Condition
H27-6 (IG+) - Body ground Ignition switch ON 11 to 14 V
H27-6 (IG+) - Body ground Ignition switch off Below 1 V


Standard Resistance:
for 12.3 Inch Display
Tester Connection Condition Specified Condition
H27-8 (GND) - Body ground Always Below 1 Ω

for 8 Inch Display
Tester Connection Condition Specified Condition
H27-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY))
a.

Disconnect the H62 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 12.3 Inch Display
Tester Connection Condition Specified Condition
H62-7 (LIN1) - H27-3 (LIN1) Always Below 1 Ω
H62-7 (LIN1) or H27-3 (LIN1) - Body ground Always 10 kΩ or higher

for 8 Inch Display
Tester Connection Condition Specified Condition
H62-7 (LIN1) - H27-8 (LIN1) Always Below 1 Ω
H62-7 (LIN1) or H27-8 (LIN1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E334619N03
0.302,1.563 0.76,1.76 0.458,0.198 10 false GND

Connect the H62 air conditioning amplifier assembly connector.


b.

Turn the ignition switch to ON.


c.

Using an oscilloscope, check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Terminal No. H62-7 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON


Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

6.INSPECT FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)
a.
B569431C01
1.625,0.104 2.063,0.365 0.438,0.26 0.99,1.854 1.167,1.854 1.167,1.854 1.823,1.313 true 1.833,0.958 1,0.375 1,0.375 0.813,0.375 true 1.719,0.146 2.177,0.344 0.458,0.198 10 false H27 0.375,1.771 1.104,2.073 0.729,0.302 10 false LIN1 (*B) 0.344,3.906 0.802,4.104 0.458,0.198 10 false GND 0.208,0.292 0.802,0.531 0.594,0.24 10 false LIN1 (*A) 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a
*A for 12.3 Inch Display
*B for 8 Inch Display
*a Component with harness connected
(Front Seat Heater Switch (Air Conditioning Control Assembly))


Connect the H27 front seat heater switch (air conditioning control assembly) connector.


b.

Turn the ignition switch to ON.


c.

Using an oscilloscope, check the waveform.

Item Content
Terminal No. H27-3 (LIN1)*1 - Body ground
H27-8 (LIN1)*2 - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

*1: for 12.3 Inch Display

*2: for 8 Inch Display


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)