Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420118 CLIMATE CONTROL SEAT SYSTEM U

SEAT  CLIMATE CONTROL SEAT SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E407961C06
1.75,0.146 2.104,0.406 0.354,0.26 2.76,0.146 3.115,0.406 0.354,0.26 3.74,0.146 4.094,0.406 0.354,0.26 4.74,0.146 5.094,0.406 0.354,0.26 5.76,0.99 5.76,0.24 5.76,0.24 5.844,0.24 true 1.802,0.198 2.115,0.375 0.313,0.177 10 false H65 2.823,0.198 3.135,0.375 0.313,0.177 10 false H64 3.802,0.198 4.115,0.375 0.313,0.177 10 false H63 4.792,0.198 5.104,0.375 0.313,0.177 10 false H62 5.927,0.156 6.24,0.333 0.313,0.177 10 false *a
*a This connector is not used by the climate control seat system. Refer to Air Conditioning System. - -


a.

Disconnect the H62 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-6 (IG+) - H62-17 (GND) IG power supply Ignition switch off Below 1 V
H62-6 (IG+) - H62-17 (GND) IG power supply Ignition switch ON 11 to 14 V
H62-5 (B) - H62-17 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H62-17 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H62 air conditioning amplifier assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-14 (LOUT) - Body ground Climate control blower control signal
·

Ignition switch ON

·

Climate control switch (Air conditioning control assembly) (for LH) on

(blower position)


Pulse generation
(See waveform)
H62-13 (ROUT) - Body ground Climate control blower control signal
·

Ignition switch ON

·

Climate control switch (Air conditioning control assembly) (for RH) on

(blower position)


Pulse generation
(See waveform)
H62-7 (LIN1) - Body ground Climate control switch signal Ignition switch ON Pulse generation

i.
B295627N02
0.156,1.594 0.594,1.833 0.438,0.24 10 false GND

Waveform (Reference):

Measurement Condition
Item Content
Tester Connection
·

H62-14 (LOUT) - Body ground

·

H62-13 (ROUT) - Body ground


Tool Setting 1 V/DIV., 0.5 ms/DIV.
Vehicle Condition
·

Ignition switch ON

·

Climate control switch (Air conditioning control assembly) on

(blower position)






CLIMATE CONTROL SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)


B567677N01
3.365,0.125 3.781,0.375 0.417,0.25 3.438,0.167 3.896,0.365 0.458,0.198 10 false H27

a.

Disconnect the H27 Climate control switch (Air conditioning control assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H27-6 (IG+) - H27-10 (GND)*1 IG power supply Ignition switch off Below 1 V
H27-4 (IG+) - H27-8 (GND)*2
H27-6 (IG+) - H27-10 (GND)*1 IG power supply Ignition switch ON 11 to 14 V
H27-4 (IG+) - H27-8 (GND)*2
H27-10 (GND) - Body ground*1 Ground Always Below 1 Ω
H27-8 (GND) - Body ground*2

*1: for 8 Inch Display

*2: for 12.3 Inch Display



c.

Reconnect the H27 Climate control switch (Air conditioning control assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H27-8 (LIN1) - H27-10 (GND)*1 Climate control switch signal Ignition switch ON Pulse generation
H27-3 (LIN1) - H27-8 (GND)*2

*1: for 8 Inch Display

*2: for 12.3 Inch Display