Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420185 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Sound Signal Circuit between Radio Receiver and Television Display Assembly  


DESCRIPTION

The television display assembly sends a sound signal to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E435910E05
0.875,0.625 1.49,0.823 0.615,0.198 10 false CDL+ 0.896,1.208 1.51,1.406 0.615,0.198 10 false CDL- 0.854,1.813 1.469,2.01 0.615,0.198 10 false CDR+ 0.875,2.406 1.49,2.604 0.615,0.198 10 false CDR- 0.177,2.865 0.49,3.063 0.313,0.198 10 false H2 0.177,3.042 1.865,3.594 1.688,0.552 10 false Radio and Display Receiver Assembly 1.333,0.51 1.49,0.708 0.156,0.198 10 false 7 5.76,0.51 5.917,0.708 0.156,0.198 10 false 7 1.333,1.115 1.49,1.313 0.156,0.198 10 false 8 5.76,1.115 5.917,1.313 0.156,0.198 10 false 8 1.333,1.708 1.49,1.906 0.156,0.198 10 false 9 5.76,1.708 5.917,1.906 0.156,0.198 10 false 9 1.333,2.292 1.781,2.594 0.448,0.302 10 false 10 5.698,2.292 6.021,2.552 0.323,0.26 10 false 10 5.698,2.896 6.021,3.156 0.323,0.26 10 false 11 3.26,2.75 4.792,2.948 1.531,0.198 10 false (Shielded) 5.708,3.615 6.833,4.083 1.125,0.469 10 false Television Display Assembly 5.708,3.438 6.167,3.719 0.458,0.281 10 false R16 5.979,0.625 6.438,0.823 0.458,0.198 10 false L1+ 5.979,1.208 6.438,1.406 0.458,0.198 10 false L1- 5.979,1.813 6.438,2.01 0.458,0.198 10 false R1+ 5.979,2.406 6.438,2.604 0.458,0.198 10 false R1- 5.979,2.927 6.677,3.156 0.698,0.229 10 false SLD1*1 5.979,3.125 6.646,3.344 0.667,0.219 10 false AGND*2 0.281,4.021 2.521,4.344 2.24,0.323 10 false *1: w/o Stereo Component Amplifier 0.281,4.344 2.521,4.667 2.24,0.323 10 false *2: w/ Stereo Component Amplifier

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the R16 television display assembly connector.


b.

Disconnect the H2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: w/o Stereo Component Amplifier

*2: w/ Stereo Component Amplifier

R16-7 (L1+) - H2-7 (CDL+) Always Below 1 Ω
R16-8 (L1-) - H2-8 (CDL-) Always Below 1 Ω
R16-9 (R1+) - H2-9 (CDR+) Always Below 1 Ω
R16-10 (R1-) - H2-10 (CDR-) Always Below 1 Ω
R16-11 (SLD1) - Body ground*1 Always 10 kΩ or higher
R16-11 (AGND) - Body ground*2 Always 10 kΩ or higher
R16-7 (L1+) or H2-7 (CDL+) - Body ground Always 10 kΩ or higher
R16-8 (L1-) or H2-8 (CDL-) - Body ground Always 10 kΩ or higher
R16-9 (R1+) or H2-9 (CDR+) - Body ground Always 10 kΩ or higher
R16-10 (R1-) or H2-10 (CDR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR