MALFUNCTION DESCRIPTION
This DTC indicates when the temperature sensor value inside the inverter has become abnormal. The cause of this malfunction may be one of the following:
Inverter internal circuit malfunction
Malfunction in ECU that controls the inverter
Malfunction in sensor for inverter control (coolant temperature sensor)
Coolant is leaking, coolant level is insufficient, coolant is frozen or coolant passage is clogged.
Grille is blocked.
Refer to the system description for the Cooling System.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Cooling System
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A9300 | Inverter "A" Cooling System Performance | ·
Inverter coolant temperature increases as well as the temperature of any inverter with converter assembly related parts due to an inverter cooling system malfunction. ·
When the actual temperature of the inverter coolant is higher than the sensor value by a certain value or more and the actual temperature is high. (1 trip detection logic) |
·
Inverter cooling system ·
Inverter water pump assembly ·
Inverter with converter assembly ·
Cooling fan system ·
Wire harness or connector ·
Grille shutter system |
Comes on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A9300 | ·
Inverter Coolant Water Temperature ·
Motor Inverter Temperature ·
Generator Inverter Calculated Temperature ·
Boosting Converter Temperature (Upper) ·
Boosting Converter Temperature (Lower) ·
Inverter Water Pump Revolution |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
With ignition switch ON and wait for 5 seconds or more.
Turn the ignition switch to ON (READY) and wait for 5 seconds or more.
Perform a road test according to the freeze frame data item "Vehicle Speed" for approximately 10 minutes.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for Cooling System.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Cooling System
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0A9300 only is output, or DTCs except the ones in the table below are also output. | A |
| DTCs of Hybrid Control System in the table below are output. | B |
| DTCs of Motor Generator Control System in the table below are output. | C |
| DTCs of SFI System in the table below are output. | D |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Insulation malfunction | Hybrid Control System | P1C7C49 | Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure |
| P1C7D49 | Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure | ||
| P1C7E49 | Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure | ||
| P1C7F49 | Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure | ||
| P1C8049 | Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure | ||
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Sensor and actuator circuit malfunction | Hybrid Control System | P0C7396 | Motor Electronics Coolant Pump "A" Component Internal Failure |
| P314A31 | Motor Electronics Coolant Pump "A" No Signal | ||
| Motor Generator Control System | P0A0011 | Motor Electronics Coolant Temperature Sensor Circuit Short to Ground | |
| P0A0015 | Motor Electronics Coolant Temperature Sensor Circuit Short to Battery or Open | ||
| System malfunction | SFI System | P059A71 | Active Grille Air Shutter "A" Actuator Stuck |
| P059A79 | Active Grille Air Shutter "A" Mechanical Linkage Failure | ||
| P05A212 | Active Grille Air Shutter "A" Circuit Short to Battery | ||
| P15AD87 | Active Grille Air Shutter "A" Missing Message | ||
P0A9300 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the ignition switch off.
A
B
C
D
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P033500
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Cooling System
If the "Cooling System" inspection results are normal, perform the next step.
| Proceed to |
|---|
| NEXT |
NEXT