Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The following procedure is for RHD vehicles.
Use the same procedure for the RH side and LH side.
The following procedure is for the RH side.
72498
1.INSTALL VERTICAL ADJUSTER BRACKET COVER (for Driver Side)
Engage the claw to install the vertical adjuster bracket cover to the front vertical adjuster brake sub-assembly.
2.INSTALL VERTICAL ADJUSTER GEAR (for Driver Side)
Install the vertical adjuster gear.
| *a | Stud Bolt of the Front Vertical Adjuster Brake Sub-assembly |
| *b | Hole of the Front Seat Adjuster Assembly |
Install the front vertical adjuster brake sub-assembly.
Make sure to insert the stud bolt of the front vertical adjuster brake sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.
Install the vertical adjuster spacer.
Install the vertical adjuster plate with the 3 nuts.
Tighten the nuts in the order shown in the illustration.
72265
3.INSTALL SEAT TRACK UPPER RAIL COVER
|
Install in this Direction |
Engage the 4 claws to install the seat track upper rail cover as shown in the illustration.
Use the same procedure for both sides.
72211
4.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 claws to install the seat track adjusting handle to the front seat adjuster assembly.
72125U
5.INSTALL REAR UPPER SEAT TRACK COVER
Operate the seat track adjusting handle and move the front seat adjuster assembly to the rearmost position.
|
Install in this Direction |
Engage the 4 claws to install the rear upper seat track cover as shown in the illustration.
Use the same procedure for both sides.
71051A
6.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
71873V
7.INSTALL FRONT RH SEAT LOWER CUSHION SHIELD (for Driver Side)
|
Install in this Direction |
Engage the claw and guide to install the front RH seat lower cushion shield as shown in the illustration.
Engage the guide first.
7181A
8.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER
w/ Wiring Harness Connector:
Engage the claw to install the wiring harness connector to the front seat cushion wire harness holder.
Engage the claw to install the front seat cushion wire harness holder.
Install the 2 screws.
71873
9.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
for RH Side:
| *a | Hook |
| *b | Guide |
Engage the 2 claws and 2 guides to install the front seat lower cushion shield RH.
Engage the hook.
for LH Side:
| *a | Hook |
| *b | Guide |
Engage the claw and guide to install the front seat lower cushion shield RH.
Engage the hook.
71875A
10.INSTALL RECLINING ADJUSTER INSIDE COVER RH (for Driver Side)
for RH Side:
Engage the 4 claws to install the reclining adjuster inside cover RH.
for LH Side:
Engage the 4 claws to install the reclining adjuster inside cover RH.
71876
11.INSTALL RECLINING ADJUSTER INSIDE COVER LH (for Front Passenger Side)
for RH Side:
Engage the 4 claws to install the reclining adjuster inside cover LH.
for LH Side:
Engage the 4 claws to install the reclining adjuster inside cover LH.
71071S
12.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Engage the 14 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the 10 hooks to install the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
Engage the 2 hooks.
for Front Passenger Side:
|
Install in this Direction |
Engage the claw to install the connector holder as shown in the illustration.
71759C
14.INSTALL FRONT NO. 1 SEATBACK HOOK
Install the 2 front No. 1 seatback hooks to the front seatback frame sub-assembly.
71587
15.INSTALL FRONT SEATBACK EDGE PROTECTOR
Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.
71053S
16.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY
|
Install in this Direction |
Install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.
Engage the 2 claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.
73910A
17.INSTALL FRONT SEAT AIRBAG ASSEMBLY
71073S
18.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Engage the 9 claws to install the separate type front seatback cover to the separate type front seatback pad.
19.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71930A
20.INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY
Engage the 4 claws to install the 2 front seat headrest support assemblies.
Close the 2 fasteners.
Engage the 3 hooks.
21.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides.
Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.
Engage the claw and 4 clamps to install the front seat airbag assembly wire harness.
Engage the claw first.
Engage the 2 hooks.
Pass the separate type front seatback cover through the grooves of each reclining adjuster inside cover RH.
71861
22.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)
|
Install in this Direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 2 claws to install the front seat inner cushion shield.
71811D
23.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 3 claws and 2 guides (B) as shown in the illustration.
Engage the 2 claws to install the front seat cushion shield.
71861
24.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
|
Install in this Direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 3 claws to install the front seat inner cushion shield.
71811D
25.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 3 claws and 2 guides (B) as shown in the illustration.
Engage the 3 claws to install the front seat cushion shield.
71848A
26.INSTALL SEAT ADJUSTER COVER CAP (for Driver Side)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 2 guides as shown in the illustration.
Engage the 2 claws to install the seat adjuster cover cap as shown in the illustration.
72525A
27.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Install the reclining adjuster release handle.
72551B
28.INSTALL RECLINING HINGE COVER
Engage the guide.
Engage the claw to install the reclining hinge cover.
72494A
29.INSTALL FRONT SEAT VERTICAL ADJUSTER HANDLE (for Driver Side)
|
Install in this Direction |
Engage the claw to install the front seat vertical adjuster handle as shown in the illustration.
71073S
30.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73230
31.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73240
32.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)