The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A27-1 (BATT) - A27-10 (E1) | Auxiliary battery (for measuring auxiliary battery voltage and ECM memory) | Always | 11 to 16 V |
| A27-2 (IGSW) - A27-10 (E1) | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| A27-6 (FPC) - A27-10 (E1) | Fuel pump control | Engine stopped, ignition switch ON | Below 1.5 V |
| A27-7 (CAN+) - A27-10 (E1) | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 1) |
| A27-8 (CANH) - A27-10 (E1) | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 1) |
| A27-9 (+B) - A27-10 (E1) | ·
Power source of ECM ·
Power source of throttle actuator |
Ignition switch ON | 11 to 14 V |
| A27-10 (E1) - Body ground | Ground | Always | Below 1 Ω |
| A27-15 (MREL) - A27-10 (E1) | EFI-MAIN NO. 1 relay operation signal | Ignition switch ON | Below 1.5 V |
| A27-16 (NEO) - A27-10 (E1) | Crankshaft revolution signal | Idling with warm engine | Pulse generation
(See waveform 2) |
| A27-17 (CAN-) - A27-10 (E1) | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 3) |
| A27-18 (CANL) - A27-10 (E1) | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 3) |
| A27-24 (G2O) - A27-10 (E1) | Camshaft revolution signal | Idling with warm engine | Pulse generation
(See waveform 4) |
| A27-32 (RFC) - A27-10 (E1) | Cooling fan control signal | Ignition switch ON, A/C switch on (max cool) | Pulse generation
(See waveform 5) |
| A27-34 (IREL) - A27-10 (E1) | D INJ relay operation signal | Ignition switch ON | 11 to 14 V |
| A27-35 (+B2) - A27-10 (E1) | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A27-36 (E2) - Body ground | Ground | Always | Below 1 Ω |
| A27-45 (EC) - Body ground | Ground | Always | Below 1 Ω |
| A27-53 (+BD1) - A27-10 (E1) | Power source of ECU (injector driver) | Ignition switch ON | 11 to 14 V |
| A27-54 (E1D1) - Body ground | Ground | Always | Below 1 Ω |
| C55-1 (M-) - A27-10 (E1) | Throttle actuator operation signal (negative signal) | Idling with warm engine | Pulse generation
(See waveform 6) |
| C55-2 (M+) - A27-10 (E1) | Throttle actuator operation signal (positive terminal) | Idling with warm engine | Pulse generation
(See waveform 7) |
| C55-3 (EGA+) - A27-10 (E1) | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 8) |
| C55-4 (EGA-) - A27-10 (E1) | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 8) |
| C55-5 (EGB-) - A27-10 (E1) | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 8) |
| C55-6 (EGB+) - A27-10 (E1) | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 8) |
| C55-8 (HA1B) - A27-10 (E1) | Air fuel ratio sensor (sensor 2) heater operation signal | Ignition switch ON | 11 to 14 V |
| Idling with cold engine | Pulse generation
(See waveform 9) |
||
| C55-9 (HA1A) - A27-10 (E1) | Air fuel ratio sensor (sensor 1) heater operation signal | Ignition switch ON | 11 to 14 V |
| Idling with cold engine | Pulse generation
(See waveform 10) |
||
| C55-10 (#2D-) - A27-10 (E1) | Direct fuel injector assembly signal (No. 2 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-11 (#2D+) - A27-10 (E1) | Direct fuel injector assembly signal (No. 2 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-12 (#3D+) - A27-10 (E1) | Direct fuel injector assembly signal (No. 3 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-13 (#3D-) - A27-10 (E1) | Direct fuel injector assembly signal (No. 3 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-14 (#4D-) - A27-10 (E1) | Direct fuel injector assembly signal (No. 4 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-15 (#4D+) - A27-10 (E1) | Direct fuel injector assembly signal (No. 4 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-16 (#1D+) - A27-10 (E1) | Direct fuel injector assembly signal (No. 1 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-17 (#1D-) - A27-10 (E1) | Direct fuel injector assembly signal (No. 1 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 11) |
| C55-18 (FP1-) - A27-10 (E1) | Fuel pump assembly (for high pressure side) signal | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C55-19 (FP1+) - A27-10 (E1) | Fuel pump assembly (for high pressure side) signal | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C55-20 (VOP-) - A27-10 (E1) | Oil pressure control valve operation signal | Idling with warm engine | Pulse generation
(See waveform 13) |
| C55-21 (VOP+) - A27-10 (E1) | Oil pressure control valve operation signal | Idling with warm engine | Pulse generation
(See waveform 13) |
| C55-26 (OE1+) - C55-25 (OE1-) | Cam timing oil control solenoid assembly operation signal | Idling | Pulse generation
(See waveform 14) |
| C55-28 (EDT1) - A27-10 (E1) | Cam timing control motor with EDU assembly signal | Idling with warm engine | Pulse generation
(See waveform 15) |
| C55-42 (WSV1) - A27-10 (E1) | Flow shutting valve operation signal | Ignition switch ON | 11 to 14 V |
| C55-46 (IGT4) - A27-10 (E1) | No. 4 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 16) |
| C55-47 (IGT3) - A27-10 (E1) | No. 3 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 16) |
| C55-48 (IGT2) - A27-10 (E1) | No. 2 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 16) |
| C55-49 (IGT1) - A27-10 (E1) | No. 1 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 16) |
| C55-50 (WPO) - A27-10 (E1) | Water inlet housing with water pump sub-assembly signal | Idling with warm engine | Pulse generation
(See waveform 17) |
| C55-51 (WPI) - A27-10 (E1) | Water inlet housing with water pump sub-assembly signal | Idling with warm engine | Pulse generation
(See waveform 18) |
| C55-62 (LIN) - A27-10 (E1) | LIN communication signal | Ignition switch ON | Pulse generation |
| C55-66 (PRG) - A27-10 (E1) | Purge VSV operation signal | Ignition switch ON | 11 to 14 V |
| Idling with warm engine, under purge control | Pulse generation
(See waveform 19) |
||
| C55-69 (VCPX)* - C55-68 (EPEX)* | Power source of differential pressure sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C55-70 (EMR1) - A27-10 (E1) | Cam timing control motor with EDU assembly signal | Idling with warm engine | Pulse generation
(See waveform 20) |
| C55-71 (EMF1) - A27-10 (E1) | Cam timing control motor with EDU assembly signal | Idling with warm engine | Below 5.0 V |
| C55-72 (EMD1) - A27-10 (E1) | Cam timing control motor with EDU assembly signal | Idling with warm engine | Pulse generation
(See waveform 21) |
| C55-73 (#40) - A27-10 (E1) | Port fuel injector assembly signal (No. 4 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 22) |
| C55-74 (#30) - A27-10 (E1) | Port fuel injector assembly signal (No. 3 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 22) |
| C55-75 (#20) - A27-10 (E1) | Port fuel injector assembly signal (No. 2 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 22) |
| C55-76 (#10) - A27-10 (E1) | Port fuel injector assembly signal (No. 1 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 22) |
| C55-78 (VCVG) - A27-10 (E1) | Power source of mass air flow meter sub-assembly (specific voltage) | Ignition switch ON | 4.8 to 5.2 V |
| C55-84 (VCPF) - A27-10 (E1) | Power source of No. 2 fuel pressure sensor (for low pressure side) (specific voltage) | Ignition switch ON | 4.75 to 5.25 V |
| C55-87 (VTA2) - C55-110 (ETA) | Throttle position sensor signal (for sensor malfunction detection) | Engine stopped, ignition switch ON, accelerator pedal fully released | 2.1 to 3.1 V |
| C55-88 (VCV1) - A27-10 (E1) | Power source of camshaft position sensor (for intake camshaft) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C55-90 (VV1+) - C55-89 (VV1-) | Camshaft position sensor (for intake camshaft) signal | Idling with warm engine | Pulse generation
(See waveform 23) |
| C55-91 (EV1+) - C55-114 (EV1-) | Camshaft position sensor (for exhaust camshaft) signal | Idling with warm engine | Pulse generation
(See waveform 23) |
| C55-92 (PEX)* - C55-68 (EPEX)* | Differential pressure sensor | Ignition switch ON | 0.4 to 4.8 V |
| C55-93 (NE+) - C55-115 (NE-) | Crankshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 24) |
| C55-94 (A1A-) - A27-10 (E1) | Air fuel ratio sensor (sensor 1) signal | Ignition switch ON | 1.24 to 4.22 V |
| C55-95 (A1A+) - A27-10 (E1) | Air fuel ratio sensor (sensor 1) signal | Ignition switch ON | 1.46 to 4.22 V |
| C55-97 (PR) - C55-96 (EPR) | Fuel pressure sensor (for high pressure side) signal | Idling with warm engine | 0.5 to 4.5 V |
| C55-98 (VCPR) - C55-96 (EPR) | Power source of fuel pressure sensor (for high pressure side) (specific voltage) | Ignition switch ON | 4.75 to 5.25 V |
| C55-99 (VCPE) - C55-100 (EPEO) | Power source of oil pressure and temperature sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C55-101 (VG) - C55-79 (E2G) | Mass air flow meter sub-assembly signal | Ignition switch ON | Pulse generation
(See waveform 25) |
| C55-102 (THA) - C55-79 (E2G) | Intake air temperature sensor (mass air flow meter sub-assembly) signal | Idling, intake air temperature 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C55-107 (PFL) - C55-61 (EPFL) | No. 2 fuel pressure sensor (for low pressure side) signal | Idling with warm engine | 0.57 to 4.88 V |
| C55-108 (VTA1) - C55-110 (ETA) | Throttle position sensor signal (for engine control) | Engine stopped, ignition switch ON, accelerator pedal fully released | 0.6 to 1.1 V |
| C55-109 (VCTA) - C55-110 (ETA) | Power source of throttle position sensor (specific voltage) | Engine stopped, ignition switch ON | 4.5 to 5.5 V |
| C55-111 (KNK1) - C55-112 (EKNK) | Knock control sensor signal | Engine speed maintained at 2500 rpm after warming up engine | Pulse generation
(See waveform 26) |
| C55-113 (VCE1) - A27-10 (E1) | Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C55-116 (VCNE) - A27-10 (E1) | Power source of crankshaft position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C55-117 (A1B-) - A27-10 (E1) | Air fuel ratio sensor (sensor 2) signal | Ignition switch ON | 1.17 to 4.49 V |
| C55-118 (A1B+) - A27-10 (E1) | Air fuel ratio sensor (sensor 2) signal | Ignition switch ON | 1.53 to 5.96 V |
| C55-120 (PIM) - C55-119 (EPIM) | Manifold absolute pressure sensor signal | Ignition switch ON | 3.0 to 4.5 V |
| C55-121 (VCPM) - C55-119 (EPIM) | Power source of manifold absolute pressure sensor (specific voltage) | Ignition switch ON | 4.75 to 5.25 V |
| C55-122 (PEO) - C55-100 (EPEO) | Engine oil pressure sensor signal | Idling with warm engine | 0.5 to 4.5 V |
| C55-123 (THEO) - C55-100 (EPEO) | Engine oil temperature sensor signal | Ignition switch ON | 0.14 to 4.93 V |
| C55-125 (THW) - C55-124 (ETHW) | Engine coolant temperature sensor signal | Idling, engine coolant temperature 75 to 100°C (167 to 212°F) | 0.2 to 1.0 V |
*: w/ Differential Pressure Sensor
WAVEFORM 1
| ECM Terminal Name | Between CANH and E1
Between CAN+ and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 2
| ECM Terminal Name | Between NEO and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 3
| ECM Terminal Name | Between CANL and E1
Between CAN- and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 4
| ECM Terminal Name | Between G2O and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 5
| ECM Terminal Name | Between RFC and E1 |
| Tester Range | 1 V/DIV., 2 ms./DIV. |
| Condition | Ignition switch ON, A/C switch on (max cool) |
The duty ratio varies depending on the engine coolant temperature.
WAVEFORM 6
| ECM Terminal Name | Between M- and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 7
| ECM Terminal Name | Between M+ and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 8
| ECM Terminal Name | CH1: Between EGA+ and E1
CH2: Between EGA- and E1 |
| CH1: Between EGB+ and E1
CH2: Between EGB- and E1 |
|
| Tester Range | 5 V/DIV., 5 μs./DIV. |
| Condition | Idling with warm engine |
When the EGR valve assembly is operating, a waveform is produced at each terminal.
WAVEFORM 9
| ECM Terminal Name | Between HA1B and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling with cold engine |
WAVEFORM 10
| ECM Terminal Name | Between HA1A and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling with cold engine |
WAVEFORM 11
| ECM Terminal Name | CH1: Between #1D+ and E1
CH2: Between #1D- and E1 |
| CH1: Between #2D+ and E1
CH2: Between #2D- and E1 |
|
| CH1: Between #3D+ and E1
CH2: Between #3D- and E1 |
|
| CH1: Between #4D+ and E1
CH2: Between #4D- and E1 |
|
| Tester Range | 50 V/DIV., 200 μs./DIV. |
| Condition | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" |
WAVEFORM 12
| ECM Terminal Name | CH1: Between FP1+ and E1
CH2: Between FP1- and E1 |
| Tester Range | 20 V/DIV., 500 μs./DIV. |
| Condition | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" |
WAVEFORM 13
| ECM Terminal Name | CH1: Between VOP+ and E1
CH2: Between VOP- and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 14
| ECM Terminal Name | Between OE1+ and OE1- |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
WAVEFORM 15
| ECM Terminal Name | Between EDT1 and E1 |
| Tester Range | 1 V/DIV., 5 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 16
| ECM Terminal Name | Between IGT (1 to 4) and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 17
| ECM Terminal Name | Between WPO and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the water inlet housing with water pump sub-assembly speed.
WAVEFORM 18
| ECM Terminal Name | Between WPI and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the water inlet housing with water pump sub-assembly speed increases.
WAVEFORM 19
| ECM Terminal Name | Between PRG and E1 |
| Tester Range | 10 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine, under purge control |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 20
| ECM Terminal Name | Between EMR1 and E1 |
| Tester Range | 2 V/DIV., 5 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 21
| ECM Terminal Name | Between EMD1 and E1 |
| Tester Range | 2 V/DIV., 100 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 22
| ECM Terminal Name | Between #10 (to #40) and E1 |
| Tester Range | 20 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine (Data List item "Injection Mode" displaying "Port") |
The wavelength becomes shorter as the engine speed increases.
When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.
WAVEFORM 23
| ECM Terminal Name | CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 24
| ECM Terminal Name | Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 25
| ECM Terminal Name | Between VG and E2G |
| Tester Range | 1 V/DIV., 100 μs./DIV. |
| Condition | Ignition switch ON |
WAVEFORM 26
| ECM Terminal Name | Between KNK1 and EKNK |
| Tester Range | 1 V/DIV., 1 ms./DIV. |
| Condition | Engine speed maintained at 2500 rpm after warming up engine |
The wavelength becomes shorter as the engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle.