| Engine idle speed (A/C OFF) | N | 650 to 750 rpm |
| Engine stall speed | D | 2070 to 2570 rpm |
| Line pressure (Wheel locked) | ||
| Engine idling | D | 500 to 700 kPa
(5.1 to 7.1 kgf/cm2, 73 to 102 psi) |
| R | 500 to 750 kPa
(5.1 to 7.6 kgf/cm2, 73 to 109 psi) |
|
| At stall speed (Throttle valve fully open) | D | 1300 to 1600 kPa
(13.3 to 16.3 kgf/cm2, 189 to 232 psi) |
| R | 1700 to 2100 kPa
(17.3 to 21.4 kgf/cm2, 247 to 305 psi) |
|
| Time lag | N → D | Less than 1.5 seconds |
| N → R | Less than 1.5 seconds | |
This check must be conducted after checking and confirming that the engine is normal.
Perform these tests with the air conditioning and cruise control off.
Do not perform the stall test for longer than 5 seconds.
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Check that there is no obstruction within 5 m (16.4 ft.) of the driving direction (forward of the vehicle when the shift lever in D, and behind the vehicle when the shift lever in R).
When torque is restricted by a safety function of the intelligent clearance sonar system, etc., the stall characteristics may not be normal.
| Solenoid (SL) valve | ||
| Tester Connection | Condition | Specified Condition |
| Solenoid (SL) valve connector terminal - Solenoid (SL) valve body | 20°C (68°F) | 11 to 15 Ω |
| Solenoid (SLT, SLU, SL1, SL2, SL3, SL4, SL5, SL6) valve | ||
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (RB) - 3 (PL)
4 (B) - 9 (L) |
Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 1 (RB) - 8 (NL)
4 (B) - 9 (L) |
Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 1 (RB) - 7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| Shift lever not in D, M, "+" or "-" | 10 kΩ or higher |
| Inspect wire harness: | ||
| Tester Connection | Condition | Specified Condition |
| 5 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 4 (STP) - Body ground | Ignition switch ON, brake pedal depressed | 11 to 14 V |
| Ignition switch ON, brake pedal released | Below 1 V | |
| 1 (E) - Body ground | Always | Below 1 Ω |
| Inspect shift lock solenoid: | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Transmission Control Switch | ||
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| 3 (SFTU) - 2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| Shift lever not held in "+" (Up-shift) | 10 kΩ or higher | |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| Shift lever not held in "-" (Down-shift) | 10 kΩ or higher | |
| Inspect the Snow switch (pattern select switch) | ||
| Tester Connection | Condition | Specified Condition |
| 5 (2ND) - 2 (E) | Snow switch on (Push) | Below 1 Ω |
| Snow switch off (Release) | 10 kΩ or higher | |
| Measurement Condition | Specified Condition | |
| Battery positive (+) → Terminal 6 (ILL+)
Battery negative (-) → Terminal 1 (ILL-) |
Illuminates | |
| Inspect the No. 1 pattern select switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 7 (SEL) - 5 (E) | Pushed and held at "DRIVE MODE +" side | Below 50 Ω |
| Released (neutral position) | 10 kΩ or higher | |
| 6 (E) - 5 (E) | Pushed and held at "DRIVE MODE -" side | Below 50 Ω |
| Released (neutral position) | 10 kΩ or higher | |
| Measurement Condition | Specified Condition | |
| Battery positive (+) → Terminal 1 (ILL+)
Battery negative (-) → Terminal 4 (ILL-) |
Illuminates | |
| Front drive shaft oil seal RH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Front drive shaft oil seal LH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Clutch return spring sub-assembly | Standard free length | 14.61 mm (0.575 in.) | |
| 1st and reverse brake return spring sub-assembly | Standard free length | 18.29 mm (0.720 in.) | |
| Planetary sun gear sub-assembly | Standard inside diameter | 33.286 to 33.312 mm (1.310 to 1.311 in.) | |
| Maximum inside diameter | 33.312 mm (1.311 in.) | ||
| Rear planetary sun gear sub-assembly | Standard inside diameter | 24.287 to 24.313 mm (0.956 to 0.957 in.) | |
| Maximum inside diameter | 24.313 mm (0.957 in.) | ||
| Front planetary gear assembly (for Outer pinion) | Standard clearance | 0.2 to 0.6 mm (0.00787 to 0.0236 in.) | |
| Front planetary gear assembly (for Inner pinion) | Standard clearance | 0.2 to 0.6 mm (0.00787 to 0.0236 in.) | |
| Rear planetary gear assembly (for Long pinion) | Standard clearance | 0.15 to 1.05 mm (0.00591 to 0.0413 in.) | |
| Rear planetary gear assembly (for Short pinion) | Standard clearance | 0.15 to 0.85 mm (0.00591 to 0.0335 in.) | |
| Input shaft end play | Standard input shaft end play | 0.332 to 1.103 mm (0.0131 to 0.0434 in.) | |
| Clearance of C-3 clutch | Pack clearance (Reference) | 0.19 to 0.61 mm (0.00748 to 0.0240 in.) | |
| Clearance of C-4 clutch | Pack clearance (Reference) | 0.27 to 0.73 mm (0.0106 to 0.0287 in.) | |
| Clearance of C-1 clutch | Pack clearance (Reference) | 1.0 to 1.2 mm (0.0394 to 0.0472 in.) | |
| Forward clutch flange thickness | Part number | Thickness (mm (in.)) | Mark |
| 35635-06130 | 4.3 (0.169) | 0 | |
| 35635-06140 | 4.4 (0.173) | 1 | |
| 35635-06150 | 4.5 (0.177) | 2 | |
| 35635-06160 | 4.6 (0.181) | 3 | |
| 35635-06170 | 4.7 (0.185) | 4 | |
| 35635-06180 | 4.8 (0.189) | 5 | |
| 35635-06190 | 4.9 (0.193) | 6 | |
| 35635-06200 | 5.0 (0.197) | 7 | |
| 35635-06210 | 5.1 (0.201) | 8 | |
| Clearance of B-1 brake | Pack clearance | 0.8 to 1.0 mm (0.0315 to 0.0394 in.) | |
| No. 1 brake flange thickness | Part number | Thickness (mm (in.)) | Mark |
| 35676-06230 | 3.5 (0.138) | 0 | |
| 35676-06240 | 3.6 (0.142) | 1 | |
| 35676-06250 | 3.7 (0.146) | 2 | |
| 35676-06260 | 3.8 (0.150) | 3 | |
| 35676-06270 | 3.9 (0.154) | 4 | |
| 35676-06280 | 4.0 (0.157) | 5 | |
| 35676-06290 | 4.1 (0.161) | 6 | |
| Clearance of C-2 clutch | Piston stroke | 0.8 to 1.0 mm (0.0315 to 0.0394 in.) | |
| Direct clutch flange thickness | Part number | Thickness (mm (in.)) | Mark |
| 35675-06140 | 3.6 (0.142) | 0 | |
| 35675-06150 | 3.7 (0.146) | 1 | |
| 35675-06160 | 3.8 (0.150) | 2 | |
| 35675-06170 | 3.9 (0.154) | 3 | |
| 35675-06180 | 4.0 (0.157) | 4 | |
| 35675-06190 | 4.1 (0.161) | 5 | |
| 35675-06200 | 4.2 (0.165) | 6 | |
| Clearance of B-2 brake | Piston stroke | 1.0 to 1.2 mm (0.0394 to 0.0472 in.) | |
| 2nd brake brake flange thickness | Part number | Thickness (mm (in.)) | Mark |
| 35678-06210 | 5.0 (0.197) | 0 | |
| 35678-06220 | 5.1 (0.201) | 1 | |
| 35678-06230 | 5.2 (0.205) | 2 | |
| 35678-06240 | 5.3 (0.209) | 3 | |
| 35678-06250 | 5.4 (0.213) | 4 | |
| 35678-06260 | 5.5 (0.217) | 5 | |
| 35678-06270 | 5.6 (0.220) | 6 | |
| Automatic transmission case straight pin | Protrusion height | 7.0 to 8.0 mm (0.276 to 0.315 in.) | |
| Front differential case tapered roller bearing preload | Standard turning torque | 0.99 to 1.28 N*m (11 to 13 kgf*cm, 9 to 11 in.*lbf) | |
| Differential drive pinion shim thickness | Part number | Thickness (mm (in.)) | Mark |
| 90564-75002 | 1.10 (0.0433) | 50 | |
| 90564-75003 | 1.13 (0.0445) | 51 | |
| 90564-75004 | 1.16 (0.0457) | 52 | |
| 90564-75005 | 1.19 (0.0469) | 53 | |
| 90564-75006 | 1.22 (0.0480) | 54 | |
| 90564-75007 | 1.25 (0.0492) | 55 | |
| 90564-75008 | 1.28 (0.0504) | 56 | |
| 90564-75009 | 1.31 (0.0516) | 57 | |
| 90564-75010 | 1.34 (0.0528) | 58 | |
| 90564-75011 | 1.37 (0.0539) | 59 | |
| 90564-75012 | 1.40 (0.0551) | 60 | |
| 90564-75013 | 1.43 (0.0563) | 61 | |
| 90564-75014 | 1.46 (0.0575) | 62 | |
| 90564-75015 | 1.49 (0.0587) | 63 | |
| 90564-75016 | 1.52 (0.0598) | 64 | |
| 90564-75017 | 1.55 (0.0610) | 65 | |
| 90564-75018 | 1.58 (0.0622) | 66 | |
| 90564-75019 | 1.61 (0.0634) | 67 | |
| 90564-75023 | 1.64 (0.0646) | 68 | |
| 90564-75024 | 1.67 (0.0657) | 69 | |
| 90564-75025 | 1.70 (0.0669) | 70 | |
| 90564-75026 | 1.73 (0.0681) | 71 | |
| 90564-75027 | 1.76 (0.0693) | 72 | |
| 90564-75028 | 1.79 (0.0705) | 73 | |
| 90564-75029 | 1.82 (0.0717) | 74 | |
| 90564-75030 | 1.85 (0.0728) | 75 | |
| 90564-75031 | 1.88 (0.0740) | 76 | |
| 90564-75032 | 1.91 (0.0752) | 77 | |
| 90564-75033 | 1.94 (0.0764) | 78 | |
| 90564-75034 | 1.97 (0.0776) | 79 | |
| 90564-75035 | 2.00 (0.0787) | 80 | |
| Pinion and counter driven gear tapered roller bearing preload | Standard turning torque | Front differential case tapered roller bearing preload + 1.75 to 2.61 N*m (18 to 26 kgf*cm, 16 to 23 in.*lbf) | |
| Pinion and counter driven gear shim thickness | Part number | Thickness (mm (in.)) | Mark |
| 90564-67047 | 1.19 (0.0469) | AA | |
| 90564-67048 | 1.22 (0.0480) | AB | |
| 90564-67049 | 1.25 (0.0492) | AC | |
| 90564-67050 | 1.28 (0.0504) | AD | |
| 90564-67051 | 1.31 (0.0516) | AE | |
| 90564-67052 | 1.34 (0.0528) | AF | |
| 90564-67053 | 1.37 (0.0539) | AG | |
| 90564-67054 | 1.40 (0.0551) | AH | |
| 90564-67055 | 1.43 (0.0563) | AJ | |
| 90564-67056 | 1.46 (0.0575) | AK | |
| 90564-67057 | 1.49 (0.0587) | AL | |
| 90564-67058 | 1.52 (0.0598) | AM | |
| 90564-67059 | 1.55 (0.0610) | AN | |
| 90564-67060 | 1.58 (0.0622) | AP | |
| 90564-67061 | 1.61 (0.0634) | AR | |
| 90564-67062 | 1.64 (0.0646) | AS | |
| 90564-67063 | 1.67 (0.0657) | AT | |
| 90564-67064 | 1.70 (0.0669) | AU | |
| 90564-67065 | 1.73 (0.0681) | AV | |
| 90564-67066 | 1.76 (0.0693) | AW | |
| 90564-67067 | 1.79 (0.0705) | AX | |
| 90564-67068 | 1.82 (0.0717) | AY | |
| 90564-67069 | 1.85 (0.0728) | AZ | |
| 90564-67071 | 1.88 (0.0740) | BA | |
| 90564-67072 | 1.91 (0.0752) | BB | |
| 90564-67073 | 1.94 (0.0764) | BC | |
| 90564-67074 | 1.97 (0.0776) | BD | |
| 90564-67075 | 2.00 (0.0787) | BE | |
| 90564-67076 | 2.03 (0.0799) | BF | |
| 90564-67077 | 2.06 (0.0811) | BG | |
| 90564-67078 | 2.09 (0.0823) | BH | |
| 90564-67079 | 2.12 (0.0835) | BJ | |
| 90564-67080 | 2.15 (0.0846) | BK | |
| 90564-67081 | 2.18 (0.0858) | BL | |
| 90564-67082 | 2.21 (0.0870) | BM | |
| Front drive shaft oil seal LH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Front drive shaft oil seal RH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Front transaxle case oil seal | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Manual valve lever shaft oil seal | Standard depth | -0.3 to 0.4 mm (-0.0118 to 0.0157 in.) | |
| Needle roller bearing | Standard depth | 2.1 to 2.5 mm (0.0827 to 0.0984 in.) | |
| Drive plate and ring gear sub-assembly | Maximum runout | 0.30 mm (0.0118 in.) |
| Stator shaft assembly (for Torque converter assembly) | Standard inside diameter | 25.201 to 25.227 mm (0.992 to 0.993 in.) |
| Maximum inside diameter | 25.227 mm (0.993 in.) | |
| Stator shaft assembly (for Oil pump drive shaft sub-assembly) | Standard inside diameter | 12.020 to 12.035 mm (0.473 to 0.474 in.) |
| Maximum inside diameter | 12.035 mm (0.474 in.) | |
| Front oil pump cover sub-assembly | Standard inside diameter | 8.02 to 8.035 mm (0.31575 to 0.31634 in.) |
| Maximum inside diameter | 8.035 mm (0.31634 in.) | |
| Front oil pump driven gear and front oil pump body | Standard body clearance | 0.135 to 0.175 mm (0.00531 to 0.00689 in.) |
| Maximum body clearance | 0.175 mm (0.00689 in.) | |
| Front oil pump driven gear and front oil pump body | Standard side clearance | 0.015 to 0.034 mm (0.000591 to 0.00134 in.) |
| Maximum side clearance | 0.034 mm (0.00134 in.) | |
| Inspect the Oil pump with solenoid assembly | ||
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
|
*: Using automatic transaxle fluid other than the above type may cause abnormal noise or vibration, or damage the transaxle of the vehicle. |
||
| Dry fill | 7.5 liters (7.9 US qts, 6.6 Imp. qts) | Toyota Genuine ATF WS* |