CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit |


| 1.CHECK VEHICLE CONTROL SYSTEM |
Check vehicle system.
| Result | Proceed to |
| w/ Multi-display | A |
| w/o Multi-display | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH) |
![]() |
Using the intelligent tester, read the Data List.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| CCS Main SW M-CPU | Cruise control main switch signal (Main CPU) / ON or OFF | ON: Cruise control main switch (Main CPU) on OFF: Cruise control main switch (Main CPU) off | - |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch on OFF: CANCEL switch off | - |
| SET/COAST Switch | -SET switch signal / ON or OFF | ON: -SET switch on OFF: -SET switch off | - |
| RES/ACC Switch | +RES switch signal / ON or OFF | ON: +RES switch on OFF: +RES switch off | - |
|
| ||||
| OK | ||
| ||
| 3.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY |

Remove the cruise control main switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 3 | Neutral | 10 kΩ or higher |
| Pushed to +RES | 235 to 245 Ω | |
| Pushed to -SET | 617 to 643 Ω | |
| Pushed to CANCEL | 1509 to 1571 Ω | |
| Main switch pushed off | 10 kΩ or higher | |
| Main switch pushed on | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT CRUISE CONTROL SWITCH WIRE |
![]() |
Remove the cruise control switch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-3 - B-3 | Always | Below 1 Ω |
| A-4 - B-1 |
|
| ||||
| OK | |
| 5.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-3 - 1 (CCS) | Always | Below 1 Ω |
| A-4 - 2 (ECC) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND) |
![]() |
Disconnect the S13 spiral cable connector.
Disconnect the E13*1 or E5*2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S13-1 (CCS) - E13-2 (CCS) | Always | Below 1 Ω |
| S13-2 (ECC) - Body ground | Always | Below 1 Ω |
| S13-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S13-1 (CCS) - E5-21 (CCS) | Always | Below 1 Ω |
| S13-2 (ECC) - Body ground | Always | Below 1 Ω |
| S13-1 (CCS) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH) |
![]() |
Using the intelligent tester, read the Data List.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| CCS Main SW M-CPU | Cruise control main switch signal (Main CPU) / ON or OFF | ON: Cruise control main switch (Main CPU) on OFF: Cruise control main switch (Main CPU) off | - |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch on OFF: CANCEL switch off | - |
| SET/COAST Switch | SET / COAST switch signal / ON or OFF | ON: SET / COAST switch on OFF: SET / COAST switch off | - |
| RES/ACC Switch | RES / ACC switch signal / ON or OFF | ON: RES / ACC switch on OFF: RES / ACC switch off | - |
|
| ||||
| OK | ||
| ||
| 8.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY |
![]() |
Remove the cruise control main switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 - 4 | Neutral | 10 kΩ or higher |
| Pushed to RES / ACC | 235 to 245 Ω | |
| Pushed to SET / COAST | 617 to 643 Ω | |
| Pushed to CANCEL | 1509 to 1571 Ω | |
| Main switch pushed off | 10 kΩ or higher | |
| Main switch pushed on | Below 1 Ω |
|
| ||||
| OK | |
| 9.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 1 (CCS) | Always | Below 1 Ω |
| 4 - 2 (ECC) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND) |
![]() |
Disconnect the S13 spiral cable connector.
Disconnect the E13*1 or E5*2 ECM connector.
*1: for 1GR-FE
*2: for 1KD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S13-1 (CCS) - E13-2 (CCS) | Always | Below 1 Ω |
| S13-2 (ECC) - Body ground | Always | Below 1 Ω |
| S13-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S13-1 (CCS) - E5-21 (CCS) | Always | Below 1 Ω |
| S13-2 (ECC) - Body ground | Always | Below 1 Ω |
| S13-1 (CCS) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||