CRUISE CONTROL SYSTEM > SYSTEM DESCRIPTION |
| CRUISE CONTROL SYSTEM (for 1GR-FE) |
| CRUISE CONTROL SYSTEM (for 1KD-FTV) |
| LIMIT CONTROL (for 1GR-FE) |
Low speed limit
The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit. The cruise control operation will be automatically canceled but the stored vehicle speed will be retained when the vehicle speed decreases below the low speed limit of 40 km/h (25 mph) while cruise control is in operation.
High speed limit
The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph). The cruise control system cannot be set when the driving vehicle speed is over the high speed limit. Also, (+RES [ACCELERATION / RESUME])*1 (RESUME / ACCEL)*2 cannot be used to increase speed beyond the high speed limit.
*1: w/ Multi-display
*2: w/o Multi-display
| LIMIT CONTROL (for 1KD-FTV) |
Low speed limit
The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit. The cruise control operation will be automatically canceled but the stored vehicle speed will be retained when the vehicle speed decreases below the low speed limit of 40 km/h (25 mph) while cruise control is in operation.
High speed limit
The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph). The cruise control system cannot be set when the driving vehicle speed is over the high speed limit. Also, (+RES [ACCELERATION / RESUME])*1 (RESUME / ACCEL)*2 cannot be used to increase speed beyond the high speed limit.
*1: w/ Multi-display
*2: w/o Multi-display
| OPERATION OF CRUISE CONTROL (for 1GR-FE) |
SET CONTROL
Vehicle speed is stored and constant speed control is maintained when pushing the switch to (-SET)*1 (SET / COAST)*2 while driving with the cruise control main switch on (the CRUISE main indicator light is on), and the vehicle speed is within the set speed range (between the low and high speed limits).
(- [COAST])*1 (COAST)*2 CONTROL
When the cruise control main switch is pushed to (-SET)*1 (SET / COAST)*2 and held in that position while the cruise control system is operating, the ECM sends a "throttle valve opening angle 0°" demand signal to the throttle body. Then the vehicle speed is stored and maintained when the cruise control main switch is released.
TAP-DOWN CONTROL
When tapping down the cruise control main switch to (-SET)*1 (SET / COAST)*2 (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and stored vehicle speeds is more than approximately 5 km/h (3.1 mph), the stored vehicle speed is set to the actual vehicle speed at the moment the cruise control main switch is released from (-SET)*1 (SET / COAST)*2 and constant speed control is maintained.
(+ [ACCELERATION])*1 (ACCEL)*2 CONTROL
The throttle valve motor of the throttle position sensor and motor is instructed by the ECM to open the throttle valve when (+RES)*1 (RESUME / ACCEL)*2 on the cruise control main switch is pressed and held while the cruise control system is in operation. When the cruise control main switch is released from (+RES)*1 (RESUME / ACCEL)*2, the vehicle speed is stored and the vehicle is controlled at a constant speed.
TAP-UP CONTROL
When tapping up the cruise control main switch to (+RES)*1 (RESUME / ACCEL)*2 (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than approximately 5 km/h (3.1 mph), the stored vehicle speed will not be changed.
(RES [RESUME])*1 (RESUME)*2 CONTROL
If cruise control operation was canceled with the stop light switch or the CANCEL switch, and if the driving speed is within the limit range, pushing the cruise control main switch to (+RES)*1 (RESUME / ACCEL)*2 restores the vehicle speed memorized at the time of cancellation, and maintains constant speed control.
MANUAL CANCEL CONTROL
Performing any of the following cancels the cruise control system while in operation (the stored vehicle speed in the ECM is maintained).
| OPERATION OF CRUISE CONTROL (for 1KD-FTV) |
SET CONTROL
Vehicle speed is stored and constant speed control is maintained when pushing the switch to (-SET)*1 (SET / COAST)*2 while driving with the cruise control main switch on (the CRUISE main indicator light is on), and the vehicle speed is within the set speed range (between the low and high speed limits).
(- [COAST])*1 (COAST)*2 CONTROL
When the cruise control main switch is pushed to (-SET)*1 (SET / COAST)*2 and held in that position while the cruise control system is operating, the ECM changes the required fuel injection quantity to 0 and decelerates the vehicle. When the cruise control main switch is released from (-SET)*1 (SET / COAST)*2, the vehicle speed is stored and constant speed control is maintained.
TAP-DOWN CONTROL
When tapping down the cruise control main switch to (-SET)*1 (SET / COAST)*2 (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and stored vehicle speeds is more than approximately 5 km/h (3.1 mph), the stored vehicle speed is set to the actual vehicle speed at the moment the cruise control main switch is released from (-SET)*1 (SET / COAST)*2 and constant speed control is maintained.
(+ [ACCELERATION])*1 (ACCEL)*2 CONTROL
While the cruise control system is in operation, if the cruise control main switch is pushed to (+RES)*1 (RESUME / ACCEL)*2, the EDU (Electronic Driving Unit) increases the fuel injection quantity. When the cruise control main switch is released from (+RES)*1 (RESUME / ACCEL)*2, the vehicle speed is stored and the vehicle is controlled at a constant speed.
TAP-UP CONTROL
When tapping up the cruise control main switch to (+RES)*1 (RESUME / ACCEL)*2 (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than approximately 5 km/h (3.1 mph), the stored vehicle speed will not be changed.
(RES [RESUME])*1 (RESUME)*2 CONTROL
If cruise control operation is canceled with the stop light switch or the CANCEL switch, and if the driving speed is within the limit range, pushing the cruise control main switch to (+RES)*1 (RESUME)*2 restores the vehicle speed memorized at the time of cancellation, and maintains constant speed control.
MANUAL CANCEL CONTROL
Performing any of the following cancels the cruise control system while in operation (the stored vehicle speed in the ECM is maintained).
| AUTO CANCEL (FAIL-SAFE) |