Home › ENGINE ยท 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > TERMINALS OF ECM

for Preparation Click here



A002958E02


HINT:
Each ECM terminal's standard normal voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard normal voltage between the terminals is shown under "Specified Condition". Use the illustration above as a reference for the ECM terminals.

Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BATT (E20-1) - E1 (E23-14)
L - BR
Battery (for measuring the battery voltage and for ECM memory)
Always
9 to 14 V
SREL (E20-2) - E01 (E23-13)
R - W-B
GLOW relay
Cranking
9 to 14 V
SREL (E20-2) - E01 (E23-13)
R - W-B
GLOW relay
Idling
(engine start and after 600 sec.)
0 to 1.5 V
MREL (E20-3) - E1 (E23-14)
W-G - BR
MAIN relay
Ignition switch ON
9 to 14 V
MREL (E20-3) - E1 (E23-14)
W-G - BR
MAIN relay
Ignition switch OFF
(after ignition switch OFF for 2 sec.)
0 to 1.5 V
TC (E20-4) - E1 (E23-14)
P-B - BR
Terminal TC of DLC3
Ignition switch ON
9 to 14 V
W (E20-5) - E1 (E23-14)
R-B - BR
MIL
MIL lights up
0 to 3 V
W (E20-5) - E1 (E23-14)
R-B - BR
MIL
MIL does not light up
9 to 14 V
THWO (E20-8) - E1 (E23-14)
P - BR
Combination meter
Ignition switch ON
Pulse generation
(See waveform 1)
SP1 (E20-9) - E1 (E23-14)
V-R - BR
Speed signal from combination meter
Ignition switch ON, rotate driving wheel slowly
Pulse generation
(See waveform 2)
STA (E20-11) - E1 (E23-14)
L-Y - BR
Starter signal
Cranking
6 V or more
+B (E20-12) - E1 (E23-14)
B - BR
Power source of ECM
Ignition switch ON
9 to 14 V
IGSW (E20-14) - E1 (E23-14)
B-O - BR
Ignition switch
Ignition switch ON
9 to 14 V
SIL (E20-15) - E1 (E23-14)
R-Y - BR
Terminal SIL of DLC3
Connect intelligent tester to DLC3
Pulse generation
STP (E20-19) - E1 (E23-14)
G-W - BR
Stop light switch
Brake pedal depressed
9 to 14 V
STP (E20-19) - E1 (E23-14)
G-W - BR
Stop light switch
Brake pedal released
Below 1.5 V
GIND (E21-1) - E1 (E23-14)
Y-R - BR
Glow indicator light
Glow indicator light lights up
0 to 3 V
GIND (E21-1) - E1 (E23-14)
Y-R - BR
Glow indicator light
Glow indicator light does not light up
9 to 14 V
AC1 (E21-2) - E1 (E23-14)
Y - BR
A/C amplifier
A/C switch ON
(magnetic clutch ON)
Below 1.5 V
AC1 (E21-2) - E1 (E23-14)
Y - BR
A/C amplifier
A/C switch OFF
7.5 to 14 V
VPA (E21-5) - EPA (E21-4)
W-L - BR-W
Accelerator pedal position sensor
(for engine control)
Ignition switch ON, accelerator pedal released
0.5 to 1.1 V
VPA (E21-5) - EPA (E21-4)
W-L - BR-W
Accelerator pedal position sensor
(for engine control)
Ignition switch ON, accelerator pedal depressed
2.6 to 4.5 V
VCPA (E21-6) - EPA (E21-4)
LG-R - BR-W
Power source of accelerator pedal position sensor
(for VPA)
Ignition switch ON
4.5 to 5.5 V
TAC (E21-7) - E1 (E23-14)
B-W - BR
Engine speed
Idling
Pulse generation
(See waveform 3)
ACT (E21-8) - E1 (E23-14)
R-L - BR
A/C amplifier
Ignition switch ON
9 to 14 V
ACT (E21-8) - E1 (E23-14)
R-L - BR
A/C amplifier
A/C cut controlled (driving below 30 km/h (18.6 mph), accelerator pedal fully depressed for 5 sec.)
0 to 3 V
ST1- (E21-11) - E1 (E23-14)
R-L - BR
Stop light switch
Brake pedal depressed
Below 1.5 V
ST1- (E21-11) - E1 (E23-14)
R-L - BR
Stop light switch
Brake pedal released
9 to 14 V
VPA2 (E21-12) - EPA (E21-4)
GR-G - BR-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal released
1.2 to 2.0 V
VPA2 (E21-12) - EPA (E21-4)
GR-G - BR-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal depressed
3.4 to 5.3 V
VC (E22-1) - E2 (E22-9)
R-W - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
PIM (E22-2) - E2 (E22-9)
L-B - BR
Manifold absolute pressure sensor
Apply vacuum 60 kPa
(450 mmHg, 17.7 in.Hg)
0.2 to 0.8 V
PIM (E22-2) - E2 (E22-9)
L-B - BR
Manifold absolute pressure sensor
Apply vacuum 207 kPa
(1,550 mmHg, 61.0 in.Hg)
4.2 to 4.8 V
THA (E22-3) - E2 (E22-9)
Y-G - BR
Intake air temperature sensor
Idling, air intake temp. 0°C (32°F) to 80°C (176°F)
0.5 to 3.4 V
THW (E22-4) - E2 (E22-9)
R-L - BR
Engine coolant temperature sensor
Idling, engine coolant temp. 60°C (140°F) to 120°C (248°F)
0.2 to 1.0 V
THF (E22-5) - E2 (E22-9)
G-B - BR
Fuel temperature sensor
Ignition switch ON (engine cold)
0.5 to 3.4 V
DATA (E22-6) - E1 (E23-14)
Y - BR
Injection pump
For 0.5 sec. after ignition switch ON
Pulse generation
CLK (E22-14) - E1 (E23-14)
L - BR
Injection pump
For 0.5 sec. after ignition switch ON
Pulse generation
THOP (E22-15) - E1 (E23-14)
GR - BR
Throttle open switch
Idling (engine warmed up)
9 to 14 V
THOP (E22-15) - E1 (E23-14)
GR - BR
Throttle open switch
Ignition switch ON (once within 5 sec.)
0 to 3 V
LU-B (E23-7) - E01 (E23-13)
L-Y - W-B
Throttle control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
LU+B (E23-8) - E01 (E23-13)
L-R - W-B
Throttle control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
LU-A (E23-9) - E01 (E23-13)
L-W - W-B
Throttle control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
LU+A (E23-10) - E01 (E23-13)
L-B - W-B
Throttle control motor
(Intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
TCV (E23-11) - E01 (E23-13)
R-W - W-B
Timing control valve
Ignition switch ON
9 to 14 V
TCV (E23-11) - E01 (E23-13)
R-W - W-B
Timing control valve
Idling
Pulse generation
(See waveform 5)
SPV+ (E23-12) - E1 (E23-14)
R-L - BR
Spill control valve
Ignition switch ON
9 to 14 V
SPV+ (E23-12) - E1 (E23-14)
R-L - BR
Spill control valve
Idling
Pulse generation
TDC+ (E23-17) - TDC- (E23-16)
R - G
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6)
NE+ (E23-19) - NE- (E23-18)
L - Y
Engine speed sensor
Idling
Pulse generation
(See waveform 6)
SPV- (E23-25) - E1 (E23-14)
R-Y - BR
Spill control valve
Idling
Pulse generation
(See waveform 7)


Waveform 1 (Reference):


    A105099E02
  1. A/C amplifier signal.
    Item
    Content
    Terminal No.
    THWO - E1
    Tool Setting
    5 V/DIV., 0.1 sec./DIV.
    Condition
    During idling

    HINT:
    Waveform time A changes according to coolant temperature.


Waveform 2 (Reference):


    A110545E02
  1. Speed signal.
    Item
    Content
    Terminal No.
    SPD - E1
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    When driving at approx. 20 km/h (12.4 mph).

    HINT:
    1. As vehicle speed increases, the waveform becomes shorter.
    2. As vehicle speed increases, the waveforms amplitude become greater.


Waveform 3 (Reference):


    A110546E04
  1. Engine speed signal.
    Item
    Content
    Terminal No.
    TAC - E1
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    1. After warming up
    2. During idling

    HINT:
    As engine speed increases, the waveform becomes shorter.


Waveform 4 (Reference):


    A110547E02
  1. Throttle control motor signal.
    Item
    Content
    Terminal No.
    LU+A, LU-A, LU+B, LU-B - E01
    Tool Setting
    10 V/DIV., 0.5 msec./DIV.
    Condition
    During engine racing


Waveform 5 (Reference):


    A002482E03
  1. Timing control value signal.
    Item
    Content
    Terminal No.
    TCV - E01
    Tool Setting
    10 V/DIV., 10 msec./DIV.
    Condition
    During idling


Waveform 6 (Reference):


    A002483E02
  1. Crankshaft position sensor signal.
    Item
    Content
    Terminal No.
    TDC+ - TDC-
    NE+ - NE-
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    During idling


Waveform 7 (Reference):


    A110550E02
  1. Spill control valve signal.
    Item
    Content
    Terminal No.
    SPV- - E1
    Tool Setting
    20 V/DIV., 10 msec./DIV.
    Condition
    During idling