Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    51    Stop Light Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.
The stop light switch has a duplex system (signals STP and ST1-) to memorize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:
The normal condition is shown in the table below.

Signal
Brake pedal released
In transition
Brake pedal depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
51
When STP (without depressing the brake pedal) and ST1- (with the brake pedal depressed) signals continue for longer than 0.5 seconds with the ignition switch ON
  1. Open or short in stop light switch signal circuit
  2. Stop light switch
  3. ECM


WIRING DIAGRAM


A119272E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


When using intelligent tester:

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light SW.

    OK:
    Brake Pedal
    Display
    Depressed
    Stop Light SW ON
    Repressed
    Stop Light SW OFF



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.CHECK ECM (STP, ST1- VOLTAGE)


    A110540E03
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Brake pedal is depressed 
    Tester Connection
    Specified Condition
    E20-19 (STP) - E23-14 (E1)
    9 to 14 V
    E21-11 (ST1-) - E23-14 (E1)
    Below 1.5 V

    Standard voltage:
    Brake pedal is released 
    Tester Connection
    Specified Condition
    E20-19 (STP) - E23-14 (E1)
    Below 1.5 V
    E21-11 (ST1-) - E23-14 (E1)
    9 to 14 V



OK
REPLACE ECM
NG


3.INSPECT STOP LIGHT SWITCH


    A072924E06
  1. Disconnect the stop light switch connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    3 - 4
    Switch pin free
    Below 1 Ω
    3 - 4
    Switch pin pushed in
    10 kΩ or higher
    1 - 2
    Switch pin free
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH
OK


4.CHECK WIRE HARNESS (ECM - STOP LIGHT SWITCH)


    A110541E03
  1. Disconnect the S14 stop light switch connector.

  1. Disconnect the E20 and E21 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance :
    Tester Connection
    Specified Condition
    S14-1 - E20-19 (STP)
    Below 1 Ω
    S14-4 - E21-11 (ST1-)
    Below 1 Ω
    E20-19 (STP) - Body ground
    10 kΩ or higher
    E21-11 (ST1-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT 


When not using intelligent tester:

1.CHECK STOP LIGHT (OPERATION)
  1. Check if the stop lights go on and off normally when the brake pedal is depressed and released.

    OK:
    The stop lights go on and off normally.



NG
REPAIR STOP LIGHT SWITCH CIRCUIT
OK


2.CHECK ECM (STP, ST1- VOLTAGE)


    A110540E03
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Brake pedal is depressed 
    Tester Connection
    Specified Condition
    E20-19 (STP) - E23-14 (E1)
    9 to 14 V
    E21-11 (ST1-) - E23-14 (E1)
    Below 1.5 V

    Standard voltage:
    Brake pedal is released 
    Tester Connection
    Specified Condition
    E20-19 (STP) - E23-14 (E1)
    Below 1.5 V
    E21-11 (ST1-) - E23-14 (E1)
    9 to 14 V



OK
REPLACE ECM
NG


3.INSPECT STOP LIGHT SWITCH


    A072924E06
  1. Disconnect the stop light switch connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    3 - 4
    Switch pin free
    Below 1 Ω
    3 - 4
    Switch pin pushed in
    10 kΩ or higher
    1 - 2
    Switch pin free
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH
OK


4.CHECK WIRE HARNESS (ECM - STOP LIGHT SWITCH)


    A110541E03
  1. Disconnect the S14 stop light switch connector.

  1. Disconnect the E20 and E21 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S14-1 - E20-19 (STP)
    Below 1 Ω
    S14-4 - E21-11 (ST1-)
    Below 1 Ω
    E20-19 (STP) - Body ground
    10 kΩ or higher
    E21-11 (ST1-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT