ECD SYSTEM (w/o EGR Cooler) > Rough Idling or Excessive Engine Vibrations |
| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|
|
|
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) | |
| Symptoms | Lack of power, black smoke | |
| Data List | MAF | |
| ||
| Main fault | Open circuit, glow plug relay fault | |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) | |
| Data List | Check the glow plug indicator light | |
| Diagnostic Point | Measure the resistance of the glow plug | |
| Main fault | Loss of compression | |
| Symptoms | Rough idle (lack of power always) | |
| Data List | Engine Speed of Cyl
| |
Diesel Injection
| Main fault | - | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
| |
| Diagnostic Trouble Code | Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored. | |
| Main fault | Blockage | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored. | |
| Main fault | Blockage | |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Injection Feedback Val
| |
| Main fault | Circuit fault: The fuel injector assembly does not open. | |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Same as injector assembly | |
| Diagnostic Trouble Code | When the injector driver has a fault, some DTCs may be stored. | |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) | |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. | |
| Main fault | - | |
| Symptoms | Difficult to start, rough idle (especially when cold) | |
Diesel EGR
| Main fault |
| |
| Symptoms |
| |
| Data List | Actual EGR Valve Pos., Target EGR Pos.
| |
Diesel Throttle
| Main fault | Stuck, does not move smoothly | |
| Symptoms |
| |
| Data List |
| |
| Data List Related to Lack of Power |
| 1.CHECK MALFUNCTION CONDITION |
Identify when shuddering occurs.
| Result | Proceed to |
| When idling | A |
| When engaging engine clutch at vehicle start | B (Clutch system shudders) |
|
| ||||
| A | |
| 2.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT |
Check the wire harness and connector connections of common rail system components.
|
| ||||
| OK | |
| 3.READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 4.TAKE SNAPSHOT DURING IDLING (PROCEDURE 4) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot when idling with no load after the engine is warmed up and when the problem is occurring.
| NEXT | |
| 5.CHECK WHITE SMOKE |
Start the engine.
Fully depress the accelerator pedal, and then release it.
Check whether white smoke is emitted when racing the engine.
| Result | Proceed to |
| White smoke is not emitted | A |
| White smoke is emitted | B |
|
| ||||
| A | |
| 6.CHECK DATA LIST (ENGINE SPEED) |
Check engine speed in the snapshot taken in procedure 4 when the engine was idling.
| Result | Proceed to |
| Change in engine speed coincides with air conditioning system operation | B |
| Except above | A |
|
| ||||
| A | |
| 7.CHECK DATA LIST (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME) |
Check Injection Feedback Val # in the snapshot taken in procedure 4 when the engine was idling.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st and engine vibration is abnormally large | A |
| Except above | B |
|
| ||||
| A | |
| 8.INSPECT INJECTOR COMPENSATION CODE |
Read the injector compensation code .
|
| ||||
| OK | |
| 9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
| NEXT | |
| 10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
| NEXT | |
| 11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 12.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the injector pilot quantity learning .
|
| ||||
| 14.REPAIR OR REPLACE HARNESS AND CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 15.CHECK AND REPAIR ENGINE ASSEMBLY |
Check the following items and repair the malfunctioning part if necessary.
Check cylinder compression pressure .
|
| ||||
| 16.CHECK AIR CONDITIONING SYSTEM |
Check the air conditioning system.
|
| ||||
| 17.CHECK DATA LIST (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Check engine speed in the snapshot taken in procedure 4 when the engine was idling after having been warmed up.
| Result | Proceed to |
| Fuel Press is more than 5000 kPa from Target Common Rail Pressure | A |
| Except above | B |
|
| ||||
| A | |
| 18.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S8-1 - E8-2 (PCV+) | Always | Below 1 Ω |
| S8-2 - E8-1 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| S8-1 or E8-2 (PCV+) - Body ground | Always | 10 kΩ or higher |
| S8-2 or E8-1 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 19.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the fuel supply pump.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump.
Reconnect the inlet hose.
|
| ||||
| OK | |
| 20.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
| NEXT | |
| 21.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 22.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
|
| ||||
| 23.REPAIR OR REPLACE HARNESS AND CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 24.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and repair or replace the clogged fuel pipe.
| NEXT | |
| 25.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
|
| ||||
| 26.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the tester while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
| Active Test | Result | Proceed to |
| Activate the EGR Valve Close: Off (Open) to On (Closed) | MAF value does not change | A |
| MAF value changes | B |
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
| Open (55%) |
| 3.0 to 9.0 gm/s |
| Closed (0%) | 13 to 20 gm/s |
|
| ||||
| A | |
| 27.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY) |
Remove the electric EGR control valve assembly.
Visually check the electric EGR control valve assembly for deposits.
If there are deposits, clean the electric EGR control valve assembly.
Reinstall the electric EGR control valve assembly.
|
| ||||
| 28.CHECK AND REPLACE ENGINE MOUNTING INSULATOR |
Check the following items and repair or replace the malfunctioning part if necessary.
Check that the engine mounting insulators are installed correctly.
Check that the engine mounting insulators are not twisted.
Check that deformation of an engine mounting insulator is not causing the engine to contact the vehicle body.
| NEXT | |
| 29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||