ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE) > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Follow the instructions on the tester and read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever is: On P or N: ON Not on P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW status (L Range) | PNP switch status/ ON or OFF | Shift lever is: On L: ON Not on L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW status (2 Range) | PNP switch status/ ON or OFF | Shift lever is: On 2: ON Not on 2: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW status (3 Range) | PNP switch status/ ON or OFF | Shift lever is: On 3: ON Not on 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW status (4 Range) | PNP switch status/ ON or OFF | Shift lever is: On 4: ON Not on 4: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW status (R Range) | PNP switch status/ ON or OFF | Shift lever is: On R: ON Not on R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW status (D Range) | PNP switch status/ ON or OFF | Shift lever is: On D: ON Not on D: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th or 5th | Shift lever position is:
| - |
| Lock Up Solenoid Status | Lock-up solenoid status/ ON or OFF |
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| SLU Solenoid Status | Shift solenoid SLU status/ ON or OFF |
| - |
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is opened or short circuited |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is opened or short circuited |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| SPD (NT) | Input turbine speed/ display: 50 r/min |
| - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| It is possible to check the operation of the shift solenoid valves. [Vehicle Condition] The vehicle speed is 50 km/h (30 mph) or less. |
| Control the Lock Up | Control shift solenoid valve SLU to set automatic transmission to lock-up condition | ON or OFF | It is possible to check the shift solenoid valve SLU operation. [Vehicle Condition]
|
| Control the Line Pressure Up* | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|