DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0705 | When either condition below is met (2 trip detection logic):
|
|

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (4 or D) | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (3 Range) | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (2 Range) | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (L Range) | PNP switch status/ ON or OFF | Shift lever:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| 1.INSPECT PARK/NEUTRAL POSITION SWITCH*1 |
![]() |
Disconnect the N1 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Specified Condition |
| 4 (B) - 5 (L) | P or N | Below 1 Ω |
| 4 (B) - 5 (L) | Not in P or N | 10 kΩ or higher |
| 1 (RL) - 2 (RB) | R | Below 1 Ω |
| 1 (RL) - 2 (RB) | Not in R | 10 kΩ or higher |
| 2 (RB) - 7 (DL) | D or 4 | Below 1 Ω |
| 2 (RB) - 7 (DL) | Not in D or 4 | 10 kΩ or higher |
| 2 (RB) - 3 (2L) | 3 | Below 1 Ω |
| 2 (RB) - 3 (2L) | Not in 3 | 10 kΩ or higher |
| 2 (RB) - 8 (LL) | 2 or L | Below 1 Ω |
| 2 (RB) - 8 (LL) | Not in 2 or L | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT SHIFT LOCK CONTROL ECU*2 |
![]() |
Disconnect the S11 ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Specified Condition |
| 9 (NSSD) - 2 (ATD) | D | Below 1 Ω |
| 9 (NSSD) - 2 (ATD) | 4 | 10 kΩ or higher |
| 9 (NSSD) - 3 (AT4) | D | 10 kΩ or higher |
| 9 (NSSD) - 3 (AT4) | 4 | Below 1 Ω |
| 10 (NSSL) - 5 (AT2) | 2 | Below 1 Ω |
| 10 (NSSL) - 5 (AT2) | L | 10 kΩ or higher |
| 10 (NSSL) - 4 (ATL) | 2 | 10 kΩ or higher |
| 10 (NSSL) - 4 (ATL) | L | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (TCM - BATTERY) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Specified Condition |
| T18-9 (R) - Body ground | R | 11 to 14 V* |
| T18-9 (R) - Body ground | Not in R | Below 1 V |
| T18-8 (D) - Body ground | D or 3 | 11 to 14 V |
| T18-8 (D) - Body ground | Not in D or 3 | Below 1 V |
| T18-13 (4) - Body ground | 4 | 11 to 14 V |
| T18-13 (4) - Body ground | Not in 4 | Below 1 V |
| T18-12 (3) - Body ground | 3 | 11 to 14 V |
| T18-12 (3) - Body ground | Not in 3 | Below 1 V |
| T18-11 (2) - Body ground | 2 or L | 11 to 14 V |
| T18-11 (2) - Body ground | Not in 2 or L | Below 1 V |
| T18-10 (L) - Body ground | L | 11 to 14 V |
| T18-10 (L) - Body ground | Not in L | Below 1 V |
|
| ||||
| OK | ||
| ||