DTC 19 (2) Accelerator Position Sensor Range / Performance Problem |

| DTC No. | DTC Detecting Condition | Trouble Area |
| 19 (2) | Either of ECM sensors completed learning, and electric potential difference of No. 1 and No. 2 sensors has become more than 1.2 V or less than 0.4 V. |
|
One of the following continues more than 2.0 seconds.
|
| Trouble area | Accelerator pedal position expressed as voltage | |||
| Accelerator pedal released | Accelerator pedal depressed | |||
| ACCEL POS #1 | ACCEL POS #2 | ACCEL POS #1 | ACCEL POS #2 | |
| VC circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| VPA circuit open or ground short | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.3 V |
| VPA2 circuit open or ground short | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| E2 circuit open | 4.5 to 5.5 V | 4.5 to 5.5 V | 4.5 to 5.5 V | 4.5 to 5.5 V |

| 1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.
Check that the value displayed on the intelligent tester changes when repeatedly depressing and releasing the accelerator pedal.
|
| ||||
| NG | |
| 2.CHECK WIRE HARNESS (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the A13 accelerator pedal position sensor connector.
Disconnect the E21 and E22 ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A13-1 (VCP2) - E22-1 (VC) | Below 1 Ω |
| A13-2 (EPA2) - E22-9 (E2) | Below 1 Ω |
| A13-3 (VPA2) - E21-12 (VPA2) | Below 1 Ω |
| A13-4 (VCPA) - E21-6 (VCPA) | Below 1 Ω |
| A13-5 (EPA) - E21-4 (EPA) | Below 1 Ω |
| A13-6 (VPA1) - E21-5 (VPA) | Below 1 Ω |
| A13-1 (VCP2) or E22-1 (VC) - Body ground | 10 kΩ or higher |
| A13-2 (EPA2) or E22-9 (E2) - Body ground | 10 kΩ or higher |
| A13-3 (VPA2) or E21-12 (VPA2) - Body ground | 10 kΩ or higher |
| A13-4 (VCPA) or E21-6 (VCPA) - Body ground | 10 kΩ or higher |
| A13-5 (EPA) or E21-4 (EPA) - Body ground | 10 kΩ or higher |
| A13-6 (VPA1) or E21-5 (VPA) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 1.CHECK ECM (VPA, VPA2 VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E21-5 (VPA) - E21-4 (EPA) | 0.5 to 1.1 V |
| E21-12 (VPA2) - E22-9 (E2) | 1.2 to 2.0 V |
| Tester Connection | Specified Condition |
| E21-5 (VPA) - E21-4 (EPA) | 2.6 to 4.5 V |
| E21-12 (VPA2) - E22-9 (E2) | 3.4 to 5.3 V |
|
| ||||
| NG | |
| 2.CHECK WIRE HARNESS (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the A13 accelerator pedal position sensor connector.
Disconnect the E21 and E22 ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A13-1 (VCP2) - E22-1 (VC) | Below 1 Ω |
| A13-2 (EPA2) - E22-9 (E2) | Below 1 Ω |
| A13-3 (VPA2) - E21-12 (VPA2) | Below 1 Ω |
| A13-4 (VCPA) - E21-6 (VCPA) | Below 1 Ω |
| A13-5 (EPA) - E21-4 (EPA) | Below 1 Ω |
| A13-6 (VPA1) - E21-5 (VPA) | Below 1 Ω |
| A13-1 (VCP2) or E22-1 (VC) - Body ground | 10 kΩ or higher |
| A13-2 (EPA2) or E22-9 (E2) - Body ground | 10 kΩ or higher |
| A13-3 (VPA2) or E21-12 (VPA2) - Body ground | 10 kΩ or higher |
| A13-4 (VCPA) or E21-6 (VCPA) - Body ground | 10 kΩ or higher |
| A13-5 (EPA) or E21-4 (EPA) - Body ground | 10 kΩ or higher |
| A13-6 (VPA1) or E21-5 (VPA) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||