ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP |
| 2. REMOVE VENTILATION VALVE |
![]() |
Loosen the hose clamp and disconnect the ventilation hose from the valve.
Remove the valve.
| 3. REMOVE CYLINDER HEAD COVER |
![]() |
Remove the 19 bolts, 2 nuts, cover and 2 gaskets.
| 4. REMOVE CRANKSHAFT PULLEY |
![]() |
Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.
Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap, as shown in the illustration.
![]() |
Using SST, hold the crankshaft pulley and remove the pulley set bolt.
![]() |
Using the set bolt and SST, remove the pulley bolt and pulley.
| 5. REMOVE NO. 2 OIL PAN |
![]() |
Remove the drain plug and gasket.
Remove the 20 bolts and 2 nuts.
Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
| 6. REMOVE OIL STRAINER |
Remove the bolt, 2 nuts, oil strainer and gasket.
| 7. REMOVE NO. 1 OIL PAN |
![]() |
Remove the 16 bolts and 2 nuts.
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
Remove the O-ring.
| 8. REMOVE TIMING CHAIN COVER |
![]() |
Remove the 19 bolts and 2 nuts shown in the illustration.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
Remove the 3 O-rings.
![]() |
Using a 10 mm socket hexagon wrench, remove the timing gear case plug.
| 9. REMOVE WATER PUMP |
![]() |
Remove the 8 bolts, water pump and gasket.
| 10. REMOVE TIMING CHAIN COVER OIL SEAL |
![]() |
Place the timing chain cover on wooden blocks.
Using a screwdriver with its tip taped, pry out the oil seal.
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
Apply a light coat of MP grease to a new oil seal lip.
| 11. REMOVE OIL PUMP RELIEF VALVE |
![]() |
Using a 27 mm socket wrench, remove the plug and gasket.
Remove the valve spring and relief valve.
| 12. REMOVE TIMING CHAIN GUIDE |
Remove the 2 bolts, timing chain guide and O-ring.
| 13. REMOVE TIMING CHAIN TENSIONER |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a 1.27 mm hexagon wrench into the stopper plate's hole.
Remove the bolt, nut, chain tensioner and gasket.
| 14. REMOVE CHAIN TENSIONER SLIPPER |
Remove the bolt and tensioner slipper.
| 15. REMOVE VIBRATION DAMPER |
Remove the 2 bolts and vibration damper.
| 16. REMOVE TIMING CHAIN |
| 17. REMOVE CRANKSHAFT TIMING SPROCKET |
| 18. REMOVE CRANKSHAFT POSITION SENSOR PLATE |
| 19. REMOVE CRANKSHAFT PULLEY SET KEY |
Remove the 2 pulley set keys from the crankshaft.
| 20. REMOVE OIL JET |
Remove the bolt, oil jet and gasket.
| 21. REMOVE CAMSHAFT |
![]() |
Uniformly loosen the 21 bearing cap bolts in several passes in the order shown in the illustration. Then remove the oil delivery pipe, O-ring and 9 bearing caps.
Remove the 9 bearing caps, oil delivery pipe, O-ring and 2 camshafts.
| 22. REMOVE CAMSHAFT TIMING SPROCKET |
![]() |
Fix the camshaft with a vise, and then remove the sprocket bolt and camshaft timing sprocket.
| 23. REMOVE CAMSHAFT TIMING GEAR |
![]() |
Remove the flange bolt of the camshaft timing gear.
| 24. REMOVE CYLINDER HEAD |
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.
Remove the cylinder head and gasket.
| 25. REMOVE OIL FILTER |
![]() |
Using SST, remove the oil filter.
| 26. REMOVE OIL FILTER UNION |
Using a 27 mm socket wrench, remove the oil filter union.
| 27. REMOVE OIL FILTER BRACKET |
Remove the oil filter bracket union bolt, gasket and oil filter union.
Remove the oil filter bracket and O-ring.
Remove the O-ring from the oil filter bracket union bolt.
| 28. REMOVE ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove the 6 bolts.
Using a screwdriver with its tip taped, pry out the oil seal retainer.
| 29. REMOVE VALVE ROCKER ARM |
| 30. REMOVE VALVE STEM CAP |
| 31. REMOVE VALVE LASH ADJUSTER |
| 32. REMOVE INTAKE VALVE |
![]() |
Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
Remove the retainer, compression spring, valve, valve spring and spring seat.
| 33. REMOVE EXHAUST VALVE |
![]() |
Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
Remove the retainer, compression spring, valve, valve spring and spring seat.
| 34. REMOVE VALVE STEM OIL SEAL |
Using needle-nose pliers, remove the oil seal.
| 35. REMOVE OIL CONTROL VALVE FILTER |
Using an 8 mm hexagon wrench, remove the screw plug.
Remove the oil control valve filter and gasket.
| 36. REMOVE NO. 1 HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm hexagon wrench, remove the 3 screw plugs.
| 37. REMOVE NO. 2 HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 9 mm hexagon wrench, remove the screw plug.
| 38. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 39. INSPECT CONNECTING ROD OIL CLEARANCE |
Check that the matchmarks on the connecting rod and cap are aligned to ensure the correct reassembly.
![]() |
Remove the 2 connecting rod cap bolts.
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
![]() |
Lay a strip of Plastigage on the crank pin.
![]() |
Install the connecting rod cap.
Match the numbered connecting rod cap with the connecting rod.
Align the pins of the connecting rod cap with the pin holes of the connecting rod, and install the connecting rod cap.
Check that the front mark of the connecting rod cap is facing forward.
![]() |
Install the connecting rod cap bolts.
Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
Install and alternately tighten the bolts of the connecting rod cap in several passes.
![]() |
Mark the front of the connecting rod cap bolts with paint.
Retighten the connecting rod cap bolts 90°as shown.
Check that the painted mark is now at a 90°angle to the front.
Remove the 2 bolts and connecting rod cap.
![]() ![]() |
Measure the Plastigage at its widest point.
| Mark | Specified Condition |
| 4 | 1.484 to 1.487 mm (0.0584 to 0.0585 in.) |
| 5 | 1.488 to 1.490 mm (0.0586 to 0.0587 in.) |
| 6 | 1.491 to 1.493 mm (0.0587 to 0.0588 in.) |
Completely remove the Plastigage.
| 40. REMOVE PISTON WITH CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 41. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| 42. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Uniformly loosen the 10 bearing cap bolts in several passes in the sequence shown in the illustration.
Clean each main journal and bearing.
Check each main journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Install the 5 crankshaft bearing caps in their proper locations.
![]() |
Install the crankshaft bearing cap bolts.
Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.
![]() |
Mark the front of the bearing cap bolts with paint.
Retighten the bearing cap bolts by 90°in the numerical order above.
Check that the painted mark is now at a 90°angle to the front.
Remove the 10 bolts and 5 crankshaft bearing caps (above procedures).
![]() ![]() |
Measure the Plastigage at its widest point.
| Item | Standard Condition |
| No. 3 journal | 0.030 to 0.055 mm (0.0012 to 0.0022 in.) |
| Other journal | 0.024 to 0.049 mm (0.0009 to 0.0019 in.) |
| Mark | Specified Condition |
| 1 | 64.004 to 64.010 mm (2.5198 to 2.5201 in.) |
| 2 | 64.011 to 64.016 mm (2.5201 to 2.5203 in.) |
| 3 | 64.017 to 64.022 mm (2.5203 to 2.5206 in.) |
| Mark | Specified Condition |
| 1 | 1.987 to 1.990 mm (0.0782 to 0.0783 in.) |
| 2 | 1.990 to 1.993 mm (0.0783 to 0.0785 in.) |
| 3 | 1.993 to 1.996 mm (0.0785 to 0.0786 in.) |
Completely remove the Plastigage.
| 43. REMOVE CRANKSHAFT |
Lift out the crankshaft.
Remove the upper bearings and upper thrust washers from the cylinder block.
| 44. REMOVE PISTON WITH PIN |
![]() |
Check fit between the piston and piston pin.
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
![]() |
Remove the piston rings.
Using a piston ring expander, remove the 2 compression rings.
Remove the rail and expander by hand.
![]() |
Disconnect the connecting rod from the piston.
Using a small screwdriver, pry off the snap ring from the piston.
![]() |
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
![]() |
Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.
| 45. REMOVE CYLINDER BLOCK WATER DRAIN COCK |
| 46. REMOVE OIL NOZZLE |
Using a 5 mm hexagon wrench, remove the oil nozzle.