FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag) > DISASSEMBLY |
| 1. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.
| 2. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the 2 screws.
Detach the rear part of the cushion shield in the order shown in the illustration, and then detach the claw and remove the cushion shield.
| 3. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) |
![]() |
w/ Driver seat belt warning light:
Detach the clamp.
![]() |
w/ Driver seat belt warning light:
Detach the wire harness from the clamp.
Remove the nut and seat belt.
Remove the buckle cover.
| 4. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) |
![]() |
w/ Passenger seat belt warning light:
Detach the 2 clamps.
w/ Passenger seat belt warning light:
Disconnect the connector.
![]() |
Detach the wire harness from the clamp.
Remove the nut and seat belt.
Remove the buckle cover.
| 5. REMOVE FRONT SEAT CUSHION COVER LH |
Remove the seat cushion cover.
| 6. REMOVE FRONT SEAT CUSHION INNER SHIELD LH |
![]() |
Remove the 2 screws.
Detach the rear part of the inner shield in the order shown in the illustration, and then remove the cushion shield.
| 7. REMOVE VERTICAL SEAT ADJUSTER KNOB RH (for RHD, w/ Vertical Adjuster) |
![]() |
Using a screwdriver, remove the snap ring as shown in the illustration.
Remove the knob.
| 8. REMOVE SEATBACK SPRING |
Remove the seatback spring.
| 9. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Detach the wire harness clamps.
Detach the 2 hooks.
Detach the hooks in the hook area shown in the illustration.
Remove the hog rings and seat cushion cover with pad from the seat cushion frame.
| 10. REMOVE FRONT SEAT CUSHION PROTECTOR |
![]() |
Remove the 2 protectors.
| 11. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the hog rings and seat cushion cover.
| 12. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Cut off the tack pins which fasten the seat heater, and then remove the front seat cushion heater from the seat cushion cover.
| 13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the hog rings from the wires of the seatback cover. Then roll up the seatback cover.
![]() |
Remove the hog rings and detach the strap of the seatback cover. Then roll up the seatback cover.
![]() |
Remove the hog rings from the center of the seatback pad and roll up the seatback cover.
![]() |
Remove the nut and detach the seatback cover bracket.
![]() |
Remove the hog rings from the upper part of the seatback pad. Then roll up the seatback cover.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
![]() |
Remove the hog rings and seatback cover.
| 14. REMOVE SEPARATE TYPE FRONT SEATBACK PAD |
![]() |
Remove the seatback pad.
| 15. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Cut off the tack pins which fasten the seat heater, and then remove the front seatback heater from the seatback cover.
| 16. REMOVE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY |
![]() |
w/ Seat Heater system:
Detach the wire harness clamps.
![]() |
Detach the wire harness clamps.
Remove the 4 bolts and seat cushion frame.
| 17. REMOVE VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (for RHD, w/ Vertical Adjuster) |
![]() |
Using a screwdriver, detach the seat spring from the reclining adjuster lower arm.
![]() |
Using a screwdriver, spread apart the tabs that hold the spring, and then remove the spring.
Using a 6 mm socket hexagon wrench, remove the front seat No. 2 adjuster pin.
![]() |
Temporarily install the vertical seat adjuster knob.
Turn the knob counterclockwise and move the gear of the vertical adjusting shaft to the position shown in the illustration.
Remove the vertical seat adjuster knob.
![]() |
Using a screwdriver, remove the 2 E-rings and vertical adjusting shaft.
| 18. REMOVE SEAT TRACK HANDLE SUB-ASSEMBLY |
![]() |
Detach the spring of the seat track in the order shown in the illustration. Then remove the handle.
| 19. REMOVE FRONT SEAT ADJUSTER ROD (for RHD, w/ Vertical Adjuster) |
![]() |
Remove the 2 bolts and front seat adjuster rod.
| 20. REMOVE RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY LH |
![]() |
Remove the 2 bolts and reclining adjuster lower arm with front seat outer track.
![]() |
for RHD, w/ Vertical Adjuster:
Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and reclining adjuster lower arm.
![]() |
w/o Vertical Adjuster:
Remove the 3 bolts and reclining adjuster lower arm.
| 21. REMOVE RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY RH |
for RHD, w/ Vertical Adjuster:
Use the same procedures described for the LH side.
w/o Vertical Adjuster:
Use the same procedures described for the LH side.
| 22. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR |
Remove the seat cushion edge protector.