Home › BODY › SEAT › REAR SEAT ASSEMBLY (for Double Cab)

REAR SEAT ASSEMBLY (for Double Cab) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
  1. Install the stopper band with a new connecting wire.

    NOTICE:
    The connecting wire cannot be reused.



2. INSTALL NO. 1 SEAT CUSHION COVER


    B257922E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



  1. for TSAM Made:



      B257931E01
    1. Set the seat cushion cover with pad in place and close the 2 fasteners.

    2. Using hog ring pliers, install new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.



  1. for TMT Made:



      B257923E01
    1. Set the seat cushion cover with pad in place and close the 2 fasteners.

    2. Using hog ring pliers, install new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the 2 cushions with the 2 screws.



3. INSTALL NO. 1 SEATBACK COVER


  1. If installing a new seatback pad:



      B112645E04
    1. Using hog ring pliers, install the seatback cover to a new seatback pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.



    2. B084943E01
    3. w/o Center headrest:
      Set the seatback cover with pad in place and attach the 8 claws to install the 4 headrest supports.



    4. B123886
    5. w/ Center headrest:
      Set the seatback cover with pad in place and attach the 12 claws to install the 6 headrest supports.



    B257924E01
  1. Using hog ring pliers, install the seatback cover with pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



  1. If installing the seatback pad with seatback frame:



      B112645E04
    1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.



    2. B084943E01
    3. w/o Center headrest:
      Attach the 8 claws to install the 4 headrest supports.



    4. B123886
    5. w/ Center headrest:
      Attach the 12 claws to install the 6 headrest supports.



    B257924E01
  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



4. INSTALL REAR SEAT CUSHION ASSEMBLY


    B084942E01
  1. Install the seat cushion with the 2 bolts.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }



5. INSTALL REAR SEAT CUSHION COVER LH


    B108084E02
  1. Attach the claw to install the cushion cover.

  1. Install the screw.



6. INSTALL REAR SEAT CUSHION COVER RH

HINT:
Use the same procedures described for the LH side.



7. INSTALL NO. 3 SEAT LEG BRACKET FRONT LH
  1. Install the bracket with the washer and nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }



8. INSTALL NO. 3 SEAT LEG BRACKET FRONT RH

HINT:
Use the same procedures described for the LH side.



9. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (w/ Center Headrest)
  1. Install the headrest.



10. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Install the 2 headrests.