Home › BRAKE › BRAKE › BRAKE BOOSTER (for TMT Made LHD)

BRAKE BOOSTER (for TMT Made LHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install a new gasket to the brake booster.



    C111300
  1. Install the booster with the 4 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. Install the push rod clevis.

  1. Apply a light coat of lithium soap base glycol grease to the clevis pin.



    C226773E01
  1. Install the clevis pin and a new clip.

    NOTICE:
    The clip must be installed as shown in the illustration.

  1. Install the return spring.

  1. Install a new grommet and check valve to the booster.

  1. Connect the vacuum hose.

  1. Install the vacuum warning switch to the booster and connect the vacuum warning switch connector

    Torque:
    14 N*m{ 139 kgf*cm , 10 ft.*lbf }



2. CHECK AND ADJUST BRAKE BOOSTER PUSH ROD (w/ ABS)

NOTICE:
The brake booster interior must not be a vacuum when adjusting the booster. Stop the engine and depress the brake pedal several times until there is no vacuum in the booster.

HINT:
Adjust the booster push rod when the master cylinder is replaced with a new one. Adjustment is not necessary when the master cylinder is reinstalled and the booster is replaced with a new one.



    C152700E01
  1. Set SST on the master cylinder, and then lower the pin until its tip slightly touches the piston.

    SST
    09737-00013  



    C152701E01
  1. Turn SST upside down, and then set it on the booster.

  1. Measure the clearance between the booster push rod and pin head (SST).

    Standard clearance:
    0 mm (0 in.)



    F040006E01
  1. To adjust the clearance of the rod, first depress the pedal so that the rod protrudes. Then fix the rod in place using SST and rotate the hexagon cap nut to adjust the clearance.

    SST
    09737-00020  



3. CHECK AND ADJUST BRAKE BOOSTER PUSH ROD (w/o ABS)

NOTICE:
The brake booster interior must not be a vacuum when adjusting the booster. Stop the engine and depress the brake pedal several times until there is no vacuum in the booster.

HINT:
Adjust the booster push rod when the master cylinder is replaced with a new one. Adjustment is not necessary when the master cylinder is reinstalled and the booster is replaced with a new one.



    C152700E01
  1. Set SST on the master cylinder, and then lower the pin until its tip slightly touches the piston.

    SST
    09737-00013  



    C152701E01
  1. Turn SST upside down, and then set it on the booster.

  1. Measure the clearance between the booster push rod and pin head (SST).

    Standard clearance:
    0 mm (0 in.)



    F040006E01
  1. To adjust the clearance of the rod, first depress the pedal so that the rod protrudes. Then fix the rod in place using SST and rotate the hexagon cap nut to adjust the clearance.

    SST
    09737-00020  



4. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)
  1. Install the brake master cylinder (Click here).



5. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS)
  1. Install the brake master cylinder (Click here).



6. FILL RESERVOIR WITH BRAKE FLUID


C122079

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



7. BLEED AIR FROM BRAKE MASTER CYLINDER


C122081

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C122083
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



8. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10.8 N*m{ 110 kgf*cm , 8 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E03



9. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)


C112661E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.



10. CHECK AND ADJUST BRAKE PEDAL HEIGHT


C111305E01
  1. Check the pedal height.

    Pedal height from dash panel:
    Model
    Specified Condition
    LHD (M/T)
    152.9 to 162.9 mm (6.020 to 6.413 in.)
    LHD (A/T)
    154.1 to 164.1 mm (6.067 to 6.461 in.)
    RHD (M/T)
    156.9 to 166.9 mm (6.177 to 6.571 in.)
    RHD (A/T)
    158.1 to 168.1 mm (6.224 to 6.618 in.)



  1. Adjust the pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Remove the switch.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the pedal height by turning the push rod.

    5. Tighten the lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    6. C111301E01
    7. Insert the switch into the adjuster until it slightly touches the pedal.

      NOTICE:
      Do not depress the pedal.



    8. C111302E01
    9. Turn the switch a quarter turn clockwise.

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

      NOTICE:
      Do not depress the pedal.

    10. Connect the connector to the switch.

    11. Check the switch clearance.

      Stop light switch clearance:
      1.5 to 2.5 mm (0.059 to 0.098 in.)



11. CHECK BRAKE PEDAL FREE PLAY


C111306E01
  1. Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.

  1. Depress the pedal until resistance is felt.

  1. Check the pedal's free play by measuring the distance between the position in the previous step and the pedal's released position.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the free play is not as specified, check the switch clearance in the next step.
    If the free play is as specified, proceed to the "check brake pedal reserve distance" procedure.

  1. Check the switch clearance.

    Stop light switch clearance:
    1.5 to 2.5 mm (0.059 to 0.098 in.)

    If the clearance is not as specified, adjust the clearance and recheck the pedal's free play.
    If the clearance is as specified, troubleshoot the brake system and proceed to the "check brake pedal reserve distance" procedure.



12. CHECK BRAKE PEDAL RESERVE DISTANCE


C111339E01
  1. Release the parking brake lever. Start the engine.

  1. Depress the pedal and check the pedal reserve distance.

    1. Depress the pedal with a force of 490 N (50 kgf, 110 lbf).

    2. Measure the distance between the pedal and dash panel shown in the illustration.

      Pedal reserve distance:
      Model
      Specified Condition
      LHD (2WD)
      78.0 mm (3.071 in.)
      LHD (4WD)
      85.0 mm (3.347 in.)
      RHD (2WD)
      82.0 mm (3.228 in.)
      RHD (4WD and pre-runner)
      89.0 mm (3.504 in.)

      If the distance is not as specified, troubleshoot the brake system.



13. CHECK BRAKE FLUID LEVEL IN RESERVOIR


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



14. CHECK FOR BRAKE FLUID LEAKAGE