Home › BRAKE › BRAKE › FRONT BRAKE (for TSAM Made 2WD)

FRONT BRAKE (for TSAM Made 2WD) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL DISC BRAKE CYLINDER ASSEMBLY LH


    C122018E02
  1. Apply silicon grease (Multemp SI-B) on contact surface of each fingers.



    C121983
  1. Install the cylinder with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



2. CONNECT FRONT FLEXIBLE HOSE


C121982
  1. Connect the flexible hose with a new gasket and a new union bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    HINT:
    Install the flexible hose lock securely in the lock hole in the cylinder.



3. FILL RESERVOIR WITH BRAKE FLUID (for LHD)


C122637

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



4. FILL RESERVOIR WITH BRAKE FLUID (for RHD)


C121862

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



5. BLEED AIR FROM BRAKE MASTER CYLINDER (for LHD)


C122638

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C122639
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



6. BLEED AIR FROM BRAKE MASTER CYLINDER (for RHD)


C121864

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C121866
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



7. BLEED AIR FROM BRAKE LINE (for LHD)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E03



8. BLEED AIR FROM BRAKE LINE (for RHD)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD and pre-runner)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E04



9. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)


C112661E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.



10. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for LHD)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



11. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for RHD)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



12. CHECK FOR BRAKE FLUID LEAKAGE


13. INSTALL FRONT WHEEL

Torque:
152 N*m{ 1550 kgf*cm , 112 ft.*lbf } for steel type
121 N*m{ 1234 kgf*cm , 89 ft.*lbf } for aluminum type