Home › BRAKE › BRAKE › FRONT BRAKE (for TSAM Made 2WD)

FRONT BRAKE (for TSAM Made 2WD) > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT DISC


C111369E01
  1. Align the matchmarks and install the disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



2. CHECK DISC RUNOUT


C115328
  1. Check the bearing play in the axial direction and check the axle hub runout .

  1. Temporarily install the disc to the hub with the hub nuts.

  1. Using a dial indicator, measure the disc runout 10.0 mm (0.39 in.) from the outer edge of the disc.

    Maximum disc runout:
    0.05 mm (0.0020 in.)

    If the runout is greater than the maximum, change the installation positions of the disc and axle so that the runout will become minimal. If the runout is greater than the maximum even when the installation positions are changed, grind the disc. If the disc thickness is less than the minimum, replace the disc.

  1. Remove the 2 nuts.



3. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG
  1. Install the bleeder plug to the cylinder.

    HINT:
    The bleeder plug will be tightened to a torque specification in the "bleed air from brake line" procedures.

  1. Install the cap.



4. INSTALL PISTON SEAL
  1. Apply lithium soap base glycol grease to a new seal.

  1. Install the seal to the cylinder.



5. INSTALL FRONT DISC BRAKE PISTON


C121992E02
  1. Apply lithium soap base glycol grease to the piston and a new cylinder boot.

  1. Install the boot to the piston.

  1. Install the piston (with boot) to the cylinder.

    NOTICE:
    Do not forcibly install the piston to the cylinder.



6. INSTALL CYLINDER BOOT


    C122015E01
  1. Using SST and a hammer, tap in the boot to the cylinder.

    SST
    09550-60010  

    NOTICE:
    1. Do not damage the boot.
    2. Install the boot securely to the cylinder.

  1. Using a screwdriver, install the set ring.

    NOTICE:
    Be careful not to damage the boot.



7. INSTALL FRONT DISC BRAKE BUSH DUST BOOT


C122649E01
  1. Apply lithium soap base glycol grease to 2 new boots.

  1. Install the 2 boots to the mounting.



8. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


    C122016E01
  1. Apply lithium soap base glycol grease to the pins and a new bush as shown in the illustration.

  1. Install the bush to the pin (lower).



    C121984
  1. Install the 2 pins (upper and lower) to the mounting.



9. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING


C111362
  1. Install the cylinder mounting with the 2 bolts.

    Torque:
    117 N*m{ 1,193 kgf*cm , 86 ft.*lbf }



10. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
  1. Install the 2 plates to the mounting.



11. INSTALL FRONT ANTI SQUEAL SHIM KIT


C122017
  1. Install the No. 1 and No. 2 shims to each pad.

    NOTICE:
    1. When replacing worn pad, the shims must be replaced together with the pads.
    2. Install the shims in the correct positions and direction.



12. INSTALL FRONT DISC BRAKE PAD
  1. Install the 2 disc brake pads to the mounting.

    NOTICE:
    There should be no oil or grease on the friction surface of the pads and disc.