REAR BRAKE FLEXIBLE HOSE (for 2WD) > INSTALLATION |
| 1. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE |
![]() |
Attach a new clip to the flexible hose.
Using a union nut wrench, connect the flexible hose to the brake tube and 3-way while holding the flexible hose with a wrench.
| 2. FILL RESERVOIR WITH BRAKE FLUID (for TMT Made LHD) |
![]() |
| 3. FILL RESERVOIR WITH BRAKE FLUID (for TMT Made RHD) |
![]() |
| 4. FILL RESERVOIR WITH BRAKE FLUID (for TSAM Made LHD) |
![]() |
| 5. FILL RESERVOIR WITH BRAKE FLUID (for TSAM Made RHD) |
![]() |
| 6. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMT Made LHD) |
![]() |
Using SST, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your finger, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using SST, connect the 2 brake lines to the master cylinder.
| 7. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMT Made RHD) |
![]() |
Using SST, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your finger, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using SST, connect the 2 brake lines to the master cylinder.
| 8. BLEED AIR FROM BRAKE MASTER CYLINDER (for TSAM Made LHD) |
![]() |
Using SST, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your finger, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using SST, connect the 2 brake lines to the master cylinder.
| 9. BLEED AIR FROM BRAKE MASTER CYLINDER (for TSAM Made RHD) |
![]() |
Using SST, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your finger, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using SST, connect the 2 brake lines to the master cylinder.
| 10. BLEED AIR FROM BRAKE LINE (for TMT Made LHD) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.

| 11. BLEED AIR FROM BRAKE LINE (for TMT Made RHD) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.

| 12. BLEED AIR FROM BRAKE LINE (for TSAM Made LHD) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.

| 13. BLEED AIR FROM BRAKE LINE (for TSAM Made RHD) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.

| 14. BLEED AIR FROM CLUTCH LINE (for Manual Transmission) |
![]() |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plug.
Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.
At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.
Repeat the previous 2 steps until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Install the bleeder plug cap.
Check that all the air has been bled out of the clutch line.
| 15. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TMT Made LHD) |
![]() |
Check the fluid level and add fluid if necessary.
| 16. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TMT Made RHD) |
![]() |
Check the fluid level and add fluid if necessary.
| 17. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TSAM Made LHD) |
![]() |
Check the fluid level and add fluid if necessary.
| 18. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TSAM Made RHD) |
![]() |
Check the fluid level and add fluid if necessary.
| 19. CHECK FOR BRAKE FLUID LEAKAGE |