Home › BRAKE › BRAKE › REAR BRAKE FLEXIBLE HOSE (for 4WD and Pre-Runner)

REAR BRAKE FLEXIBLE HOSE (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE


    C111602
  1. Attach a new clip to the flexible hose.

  1. Using a union nut wrench connect the flexible hose to the brake tube and 3-way while holding the flexible hose with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake tube and 3-way from the connecting points.
    3. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



2. FILL RESERVOIR WITH BRAKE FLUID (for TMT Made LHD)


C122079

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



3. FILL RESERVOIR WITH BRAKE FLUID (for TMT Made RHD)


C122080

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



4. FILL RESERVOIR WITH BRAKE FLUID (for TSAM Made LHD)


C122637

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



5. FILL RESERVOIR WITH BRAKE FLUID (for TSAM Made RHD)


C121862

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



6. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMT Made LHD)


C122081

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C122083
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



7. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMT Made RHD)


C122082

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C122084
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



8. BLEED AIR FROM BRAKE MASTER CYLINDER (for TSAM Made LHD)


C122638

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C122639
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



9. BLEED AIR FROM BRAKE MASTER CYLINDER (for TSAM Made RHD)


C121864

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C121866
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



10. BLEED AIR FROM BRAKE LINE (for TMT Made LHD)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10.8 N*m{ 110 kgf*cm , 8 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E03



11. BLEED AIR FROM BRAKE LINE (for TMT Made RHD)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10.8 N*m{ 110 kgf*cm , 8 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E03



12. BLEED AIR FROM BRAKE LINE (for TSAM Made LHD)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E03



13. BLEED AIR FROM BRAKE LINE (for TSAM Made RHD)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD and pre-runner)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E04



14. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)


C112661E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.



15. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TMT Made LHD)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



16. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TMT Made RHD)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



17. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TSAM Made LHD)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



18. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TSAM Made RHD)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



19. CHECK FOR BRAKE FLUID LEAKAGE