TRANSFER ASSEMBLY > DISASSEMBLY |
| 1. REMOVE TRANSFER INDICATOR SWITCH |
![]() |
Remove the switches and gaskets.
| No. 1 | Indicator switch (neutral position) for A/T |
| No. 2 | Indicator switch (L4 position) for A/T or M/T w/ ABS |
| No. 3 | Indicator switch (4WD) for A/T and M/T |
| 2. REMOVE TRANSFER GEAR SHIFT HEAD (for Adapter on Type) |
![]() |
Using a pin punch and hammer, remove the 2 slotted pins from the No. 1 and No. 2 gear shift heads.
Remove the No. 1 and No. 2 gear shift heads from the front drive shift fork shaft, and high and low shift fork shaft.
| 3. REMOVE TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY (for Transfer on Type) |
![]() |
Remove the 4 bolts and retainer.
| 4. REMOVE TRANSFER CASE COVER SUB-ASSEMBLY (for Adapter on Type) |
![]() |
Remove the 4 bolts and case cover.
| 5. REMOVE BREATHER OIL DEFLECTOR |
| 6. REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY |
![]() |
Remove the 5 bolts and bearing retainer.
| 7. REMOVE TRANSFER COVER OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal from the bearing retainer.
| 8. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front) |
Using a chisel and hammer, loosen the staked part of the lock nut.
![]() |
Using SST to hold the companion flange, remove the lock nut.
![]() |
Using SST, remove the companion flange.
| 9. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Front) |
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
| 10. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear) |
Remove the companion flange (rear) in the same way as the companion flange (front).
| 11. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear) |
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
| 12. REMOVE SPEED SENSOR |
![]() |
Disconnect the sensor connector.
Remove the bolt and sensor with driven gear.
| 13. REMOVE SPEEDOMETER DRIVEN GEAR SUB-ASSEMBLY |
![]() |
Remove the clip and driven gear from the sensor.
![]() |
Remove the O-ring from the driven gear.
| 14. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY |
Remove the 5 bolts and extension housing.
| 15. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal.
| 16. REMOVE TRANSFER OUTPUT SHAFT WASHER |
| 17. REMOVE TRANSFER SPEEDOMETER DRIVE GEAR |
| 18. REMOVE REAR TRANSFER CASE |
![]() |
Remove the 12 bolts and clamp.
Remove the rear case.
| 19. REMOVE FRONT TRANSFER DRIVE SHIFT FORK SHAFT |
![]() |
Using a hexagon wrench, remove the 2 plugs.
Using a magnetic finger, remove the 2 springs and 2 balls from both holes.
Mount the case rear in a vise.
![]() |
Using a pin punch and hammer, tap out the 2 slotted pins from the shift shaft stopper and No. 2 gear shift fork.
![]() |
Hold the shift fork shaft in place by hand when removing the pin punch.
![]() |
Remove the shift fork shaft, No. 1 gear shift fork, spring and shift shaft stopper.
![]() |
Using a magnetic finger, remove the straight pin.
| 20. REMOVE TRANSFER HIGH AND LOW SHIFT FORK SHAFT |
![]() |
Remove the shift fork shaft and No. 2 gear shift fork.
| 21. REMOVE TRANSFER REAR OUTPUT SHAFT, FRONT TRANSFER DRIVE CHAIN AND TRANSFER DRIVEN SPROCKET |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Using a plastic-faced hammer, carefully tap the case rear, and remove the output shaft together with the drive chain and driven sprocket.
Remove the output shaft and driven sprocket from the drive chain.
| 22. REMOVE TRANSFER DRIVEN SPROCKET BEARING |
![]() |
Using a press, press out the bearing.
| 23. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING |
![]() |
Using SST, a press and steel bar, press out the bearing.
| 24. REMOVE NO. 1 TRANSFER CASE PLUG (for Filler) |
Remove the filler plug and gasket.
| 25. REMOVE NO. 1 TRANSFER CASE PLUG (for Drain) |
Remove the drain plug and gasket.
| 26. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and oil separator.
| 27. REMOVE TRANSFER CASE MAGNET |
| 28. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and oil pump body.
| 29. REMOVE TRANSFER OIL PUMP BODY O-RING |
![]() |
Using a screwdriver, remove the O-ring from the oil pump body.
| 30. REMOVE TRANSFER OIL PUMP GEAR |
![]() |
Remove the nut and oil pump gear.
| 31. REMOVE FRONT TRANSFER DRIVE CLUTCH SYNCHRONIZER RING (for Manual Transmission) |
![]() |
Remove the synchronizer ring from the planetary gear.
| 32. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Remove the low planetary gear with the input shaft.
| 33. REMOVE TRANSFER CASE PLUG |
![]() |
| 34. REMOVE COMPRESSION SPRING |
| 35. REMOVE PIN |
| 36. REMOVE TRANSFER LOW PLANETARY RING GEAR |
![]() |
Using a screwdriver, pry out the snap ring.
Remove the ring gear from the case front.
| 37. REMOVE TRANSFER CASE OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal (No. 1).
Using a screwdriver and hammer, tap out the oil seal (No. 2).
| 38. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE |
![]() |
Using a screwdriver, pry out the snap ring.
![]() |
Remove the spline piece.
| 39. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING |
![]() |
| 40. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING |
![]() |
Using a snap ring expander, remove the snap ring.
| 41. REMOVE TRANSFER INPUT GEAR STOPPER |
![]() |
| 42. REMOVE TRANSFER INPUT GEAR STOPPER BALL |
| 43. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER |
| 44. REMOVE TRANSFER INPUT SHAFT |
![]() |
| 45. REMOVE NO. 1 TRANSFER THRUST BEARING RACE |
| 46. REMOVE TRANSFER LOW PLANETARY GEAR BEARING |
| 47. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING |
![]() |
Remove the 2 seal rings.
| 48. REMOVE TRANSFER INPUT SHAFT BEARING |
Using a snap ring expander, remove the snap ring.
![]() |
Using SST and a press, press out the bearing.
| 49. REMOVE TRANSFER LOW PLANETARY GEAR BEARING |
![]() |
Using SST, remove the bearing.
| 50. REMOVE TRANSFER CLUTCH HUB (for Manual Transmission) |
![]() |
Using a snap ring expander, remove the snap ring.
Remove the high and low clutch sleeve, 3 shifting keys and 2 shifting key springs.
Using a press, press out the clutch hub.
| 51. REMOVE TRANSFER CLUTCH HUB (for Automatic Transmission) |
Using a snap ring expander, remove the snap ring.
Remove the high and low clutch sleeve.
Using a press, press out the clutch hub.
| 52. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY (for A.D.D. Manual Shift Type) |
![]() |
Using SST and a press, press out the bearing.
![]() |
Remove the spacer and ball.
Remove the drive sprocket with front drive clutch sleeve.
Remove the needle roller bearing.
Remove the front drive synchronizer ring.
Remove the front drive sleeve, 3 shifting keys and 2 shifting key springs from the drive sprocket.
| 53. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY (for Normal Shift Type) |
![]() |
Using SST and a press, press out the bearing.
![]() |
Remove the spacer and ball.
Remove the drive sprocket with front drive clutch sleeve.
Remove the needle roller bearing.