Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL

REAR DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT

for Preparation Click here



1. REMOVE REAR PROPELLER SHAFT ASSEMBLY
(Click here)


2. REMOVE REAR DRIVE PINION NUT


C089309E01
SST
09330-00021  
  1. Using SST and a hammer, loosen the staked part of the nut.



    B087842E02
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



3. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F040720E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



4. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


F040717E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  



5. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


6. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


F040718E01
  1. Using SST, remove the roller bearing (inner).

    SST
    09556-22010  
    09308-00010  



    W001770E02
  1. Using SST, tap out the roller bearing (outer).



7. REMOVE DIFFERENTIAL OIL STORAGE RING
  1. Using a screwdriver and hammer, tap out the oil storage ring.



8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


C093595E01
  1. Install a new bearing spacer.

    HINT:
    Be careful of the installation direction of the spacer.



10. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.



11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


G021735E01
  1. Using SST and a hammer, tap in a new roller bearing (outer).

    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).



12. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


13. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


C227961E01
  1. for TMC Made:

    1. Using SST and a hammer, tap in a new oil seal.

      SST
      09554-30011  

      Standard oil seal depth:
      0 +/-0.3mm (0 +/-0.0118in.)

    2. Apply MP grease to the lip of the oil seal.

  1. for DANA Made:

    1. Using a brass bar and hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

      NOTICE:
      Do not damage the oil seal.

    2. Apply MP grease to the lip of the oil seal.



14. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F040716E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



    B087843E01
  1. Using SST to hold the companion flange in place, install the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3,770 kgf*cm , 27 ft.*lbf } or less



15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C089308E01
  1. Using a torque wrench, measure the preload.

    Preload (at start of torque):
    Item
    Specified Condition
    New bearing
    1.05 to 1.64 N*m (11 to 17 kgf*cm, 9.3 to 15 in.*lbf)
    Reused bearing
    0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf)

    1. If the result is not as specified, adjust the preload.



16. STAKE DRIVE PINION NUT


C089310E01
  1. Using a chisel and hammer, stake the nut.



17. INSTALL REAR PROPELLER SHAFT ASSEMBLY
(Click here)


18. REFILL DIFFERENTIAL OIL


D025304E05
  1. Stop the vehicle on a level surface.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    1. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Item
    Temperature
    Viscosity
    Front differential (w/ A.D.D.)
    SAE 75W-90
    Front differential (w/o A.D.D.)
    Rear differential
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 85W-90

    Differential oil type:
    Item
    Oil type
    Front differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard front differential oil capacity:
    Item
    Capacity
    w/o A.D.D.
    1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.)
    w/ A.D.D.
    1.60 to 1.70 liters (1.69 to 1.80 US qts., 1.40 to 1.50 Imp. qts.)

    TMT made Standard rear differential oil capacity:
    Item
    Capacity
    2WD and w/ LSD
    3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.)
    4WD and w/o LSD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)

    TSAM made :
    Item
    Capacity
    2WD and made for DANA
    2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
    4WD, Pre-runner and made for DANA
    (w/o LSD, A.D.D.)
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ LSD for 2WD
    3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.)
    w/ LSD for 4WD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug with a new gasket.

    Torque:
    Front differential:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }
    Rear differential:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



19. CHECK FOR DIFFERENTIAL OIL LEAKAGE


D025304E05
  1. Stop the vehicle on a level surface.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    1. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Item
    Temperature
    Viscosity
    Front differential (w/ A.D.D.)
    SAE 75W-90
    Front differential (w/o A.D.D.)
    Rear differential
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 85W-90

    Differential oil type:
    Item
    Oil type
    Front differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard front differential oil capacity:
    Item
    Capacity
    w/o A.D.D.
    1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.)
    w/ A.D.D.
    1.60 to 1.70 liters (1.69 to 1.80 US qts., 1.40 to 1.50 Imp. qts.)

    TMT made Standard rear differential oil capacity:
    Item
    Capacity
    2WD and w/ LSD
    3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.)
    4WD and w/o LSD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)

    TSAM made :
    Item
    Capacity
    2WD and made for DANA
    2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
    4WD, Pre-runner and made for DANA
    (w/o LSD, A.D.D.)
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ LSD for 2WD
    3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.)
    w/ LSD for 4WD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug with a new gasket.

    Torque:
    Front differential:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }
    Rear differential:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }