REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > REASSEMBLY |
| 1. ASSEMBLE DIFFERENTIAL CASE |
![]() |
Install the side gear thrust washer to the side gear.
Install the 4 rear differential pinion thrust washers to the 4 rear drive pinion gears.
Install the 4 rear differential pinion thrust washers and 4 rear drive pinion gears to the spider.
Fix the differential case RH.
![]() |
Install the rear differential side gear and rear differential spider to the differential case RH.
![]() |
Using a dial indicator, measure the differential case RH side backlash while holding the pinion toward the case.
Remove the rear differential spider from the differential case RH.
![]() |
Install the rear differential side gear and rear differential spider to the differential case LH.
Using a dial indicator, measure the differential case LH side backlash while holding the pinion toward the case.
| Thickness | Thickness |
| 0.90 mm (0.035 in.) | 1.20 mm (0.047 in.) |
| 1.00 mm (0.039 in.) | 1.30 mm (0.051 in.) |
| 1.10 mm (0.043 in.) | - |
![]() |
Align the matchmarks and assemble the RH and LH cases.
Using a plastic-faced hammer, install the differential case.
Install the 8 bolts.
| 2. INSTALL DIFFERENTIAL RING GEAR |
![]() |
Clean the contact surfaces of the differential case and ring gear.
Heat the ring gear in boiling water that is approximately 100°C (212°F).
Carefully remove the ring gear from the boiling water.
After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.
![]() |
Align the matchmarks on the ring gear with those of the differential case.
Temporarily install 5 new lock plates and 10 bolts.
After the ring gear cools down, install the 8 bolts by diametrically tightening the bolts uniformly in several passes.
![]() |
Using a chisel and hammer, stake the 5 lock plates.
| 3. INSTALL REAR DIFFERENTIAL CASE BEARING |
![]() |
Using SST and a press, press the bearing onto the differential case.
| 4. INSPECT DIFFERENTIAL RING GEAR RUNOUT |
![]() |
Install the differential case on the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.
Install the 2 bearing caps with the 4 bolts.
Using a dial indicator, measure the runout of the ring gear.
Remove the 2 bearing caps, 2 adjusting nuts and differential case.
| 5. INSTALL REAR DIFFERENTIAL DUST DEFLECTOR |
![]() |
Using SST, a plate and a press, press in the dust deflector.
| 6. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press the roller bearing (outer) to the carrier.
| 7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press the roller bearing (outer) into the carrier.
| 8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Install the plate washer on the drive pinion.
Using SST and a press, press the roller bearing (inner) onto the drive pinion.
| 9. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Install the drive pinion, rear drive pinion front tapered roller bearing and rear differential drive pinion oil slinger.
![]() |
Using SST, install the companion flange.
![]() |
Adjust the drive pinion preload by tightening the companion flange nut.
Using SST to hold the companion flange in place, torque the nut.
Using a torque wrench, measure the preload.
| Bearing | Preload |
| New bearing | 1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf) |
| Reused bearing | 0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 4.9 to 7.5 in.*lbf) |
| 10. INSTALL DIFFERENTIAL CASE ASSEMBLY |
![]() |
Apply MP grease on the rack of the shift fork and connecting part of the indicator switch.
Insert the shift fork into the differential carrier, as shown in the illustration.
![]() |
Place the outer race and adjusting nut on the left side of the sleeve.
![]() |
Install the shift fork in the groove of the sleeve holding it by hand, and install the case in the carrier.
| 11. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT |
![]() |
Install the 2 adjusting nuts on the carrier, making sure the nuts are threaded properly.
| 12. INSPECT AND ADJUST BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION |
![]() |
Align the matchmarks on the cap and carrier.
![]() |
Install the right and left bearing caps with the 4 bolts.
![]() |
Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned by SST.
Using SST, torque the adjusting nut on the ring gear side until the ring has a backlash of about 0.2 mm (0.008 in.).
![]() |
While turning the ring gear, use SST to fully tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.
Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.
![]() |
Using a dial indicator, adjust the ring gear backlash until it is within the specification.
![]() |
Torque the bearing cap bolts.
| 13. INSPECT TOTAL PRELOAD |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| 14. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION |
![]() |
Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead primer.
Hold the companion flange firmly in place and rotate the ring gear in both directions.
Inspect the tooth contact pattern.

![]() |
| Thickness mm (in.) | Thickness mm (in.) |
| 1.69 to 1.71 (0.0665 to 0.0673) | 2.02 to 2.04 (0.0795 to 0.0803) |
| 1.72 to 1.74 (0.0677 to 0.0685) | 2.05 to 2.07 (0.0807 to 0.0815) |
| 1.75 to 1.77 (0.0689 to 0.0697) | 2.08 to 2.10 (0.0819 to 0.0827) |
| 1.78 to 1.80 (0.0701 to 0.0709) | 2.11 to 2.13 (0.0831 to 0.0839) |
| 1.81 to 1.83 (0.0713 to 0.0720) | 2.14 to 2.16(0.0843 to 0.0850) |
| 1.84 to 1.86 (0.0724 to 0.0732) | 2.17 to 2.19 (0.0854 to 0.0862) |
| 1.87 to 1.89 (0.0736 to 0.0744) | 2.20to 2.22 (0.0866 to 0.0874) |
| 1.90 to 1.92 (0.0748 to 0.0756) | 2.23 to 2.25 (0.0878 to 0.0886) |
| 1.93 to 1.95 (0.0760 to 0.0768) | 2.26 to 2.28 (0.0890 to 0.0898) |
| 1.96 to 1.98 (0.0772 to 0.0780) | 2.29 to 2.31 (0.0902 to 0.0909) |
| 1.99 to 2.01 (0.0783 to 0.0791) | 2.32 to 2.34 (0.0913 to 0.0921) |
| 15. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange in place, remove the nut.
| 16. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
| 17. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 18. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (outer) from the carrier.
Using a brass bar and hammer, tap out the oil storage ring from the carrier.
| 19. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() |
Install a new bearing spacer to the drive pinion.
| 20. INSTALL DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
| 21. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
| 22. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 23. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
for TMC Made:
Using SST and a hammer, tap in a new oil seal.
Apply MP grease to the lip of the oil seal.
for DANA Made:
Using a brass bar and hammer, tap in a new oil seal until its surface is flush with the differential carrier end.
Apply MP grease to the lip of the oil seal.
| 24. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, install the companion flange on the drive pinion.
![]() |
Coat the threads of a new nut with hypoid gear oil LSD.
Using SST to hold the flange, torque the nut.
| 25. INSPECT DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Bearing | Preload |
| New bearing | 1.05 to 1.64 N*m (11 to 17 kgf*cm, 9.3 to 15 in.*lbf) |
| Reused bearing | 0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf) |
| 26. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload.
| 27. INSPECT DIFFERENTIAL RING GEAR BACKLASH |
![]() |
Using a dial indicator, measure the backlash of the ring gear.
| 28. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.
| Runout | Maximum |
| Vertical runout | 0.10 mm (0.0039 in.) |
| Lateral runout | 0.10 mm (0.0039 in.) |
| 29. STAKE DRIVE PINION NUT |
![]() |
Using a chisel and hammer, stake the nut.
| 30. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK |
![]() |
Install 2 new adjusting locks on the bearing caps with the 2 bolts.
Bend the nut locks.
| 31. INSTALL REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT |
![]() |
Apply MP grease onto the outer circuit of the fork shaft.
Install the fork shaft to match the hole of the shift fork and that of the shift fork shaft.
![]() |
Remove any seal packing material and be careful not to drop oil on the contacting surface of the differential carrier and shaft retainer.
Apply seal packing to the carrier, as shown in the illustration.
![]() |
Clean the threads of the bolts and retainer bolts holes with toluene or trichloroethylene.
Apply adhesive to 2 or 3 threads of the mounting bolt end.
Tighten the shaft retainer with the 2 bolts.
![]() |
Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the shift fork.
![]() |
Shift the fork to the lock side.
![]() |
Install the steel ball, spring and spring seat.
Clean the threads of the 2 plug holes with toluene or trichloroethylene.
Apply adhesive to the plug threads.
Using a 6 mm hexagon wrench, install and tighten the screw plugs.
| 32. INSPECT REAR DIFFERENTIAL LOCK SLEEVE |
![]() |
Measure the distance between the sleeve and tip of the differential case when the differential is free and locked, respectively.
| Position | Specified Condition |
| Lock | 17.44 to 18.86 mm (0.6866 to 0.7425 in.) |
| Free | 32.40 to 33.90 mm (1.2756 to 1.3346 in.) |
| 33. INSTALL NO. 1 TRANSFER INDICATOR SWITCH |
![]() |
Install the indicator switch with a new gasket.
| 34. INSTALL DIFFERENTIAL LOCK SHIFT ACTUATOR |
![]() |
Install a new O-ring to the actuator.
Install the actuator with the bolt.
Check that the outermost rack tooth of the shift fork is virtually above the center line of the actuator installation hole.
![]() |
Ensure that the matchmarks on the pinion of the actuator are in the range between 0 and 5° clockwise above the center line of the actuator.
Install a new O-ring to the actuator.
Apply a light coat of gear oil to the O-ring.
Apply MP grease to the gear parts.
![]() |
Ensure that the outermost rack tooth of the shift fork fits the matchmarks on the pinion of the actuator.
Install the actuator so that the long hole on the actuator side fits with the knock pin on the carrier side.
Align the actuator with the long hole and rotate the actuator counterclockwise when the knock pin is set to the right-hand side.
Install and tighten the bolts.