AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Inspect the torque converter clutch assembly (Click here ).
| 2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY |
![]() |
Install the torque converter clutch to the automatic transmission.
Using a vernier caliper and straightedge, measure dimension A between the transmission and the end surface of the drive plate.
![]() |
Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A.
| 3. INSTALL TRANSFER ASSEMBLY |
Install the transfer assembly (Click here).
| 4. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR |
![]() |
Install the engine mounting insulator to the transmission with the 4 bolts.
| 5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Install the transmission to the engine with the 7 bolts.
![]() |
Install the exhaust manifold stay with the 3 bolts.
![]() |
Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch mounting bolts.
| 6. INSTALL FLYWHEEL HOUSING DUST SEAL |
| 7. CONNECT WIRE HARNESS |
| 8. CONNECT CONNECTOR |
Transmission side:
Connect the connectors.
Connect the temperature sensor connector.
Connect the park/neutral position switch connector.
Connect the 2 speed sensor connectors.
Connect the transmission wire connector.
Transfer side:
Connect the connectors.
Connect the indicator switch connector (for 4WD).
Connect the speedometer sensor connector.
Connect the indicator switch connector (for L4).
Connect the indicator switch connector (neutral).
| 9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
*1: Install the 4 set bolts of the engine mounting insulator.
*2: Install the frame crossmember with the 4 bolts and 4 nuts.
| 10. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter with the 2 bolts.
Install the starter wire to terminal 30 with the nut.
Connect the starter connector.
| 11. INSTALL FRONT FENDER SEAL |
Install the fender seal with the 5 clips.
| 12. INSTALL TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Install the control cable bracket with the 2 bolts.
| 13. CONNECT TRANSMISSION CONTROL SHIFT CABLE ASSEMBLY |
![]() |
Connect the control cable with the clip.
Connect the control cable with the nut.
| 14. INSTALL OIL COOLER TUBE |
![]() |
Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.
Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.
Install the 3 clamps with the 3 bolts.
![]() |
Using a union nut wrench, tighten the inlet and outlet tubes.
| 15. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY |
![]() |
Coat a new O-ring with ATF, and install it to the oil filler tube.
Install the oil filler tube with the 2 bolts.
Install the oil dipstick.
| 16. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
Install the propeller with center bearing shaft assembly (Click here).
| 17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
Install the front propeller shaft assembly (Click here).
| 18. INSTALL TRANSFER CASE LOWER PROTECTOR |
Install the transfer case lower protector with the 4 bolts.
| 19. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
Install the front pipe to the pipe support.
![]() |
Install a new gasket to the exhaust manifold.
Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.
![]() |
Attach the 3 wire clamps to the vehicle body.
Connect the heated oxygen sensor connector.
Connect the front pipe to the center pipe with a new gasket, 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.
| 20. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY |
![]() |
Install the transfer shift lever to the shift lever retainer.
Using needle-nose pliers, install the snap ring.
Install the shift lever boot with the 4 bolts.
| 21. INSTALL SHIFT LEVER BOOT ASSEMBLY |
Install the shift lever boot with the 4 screws.
| 22. ADJUST SHIFT LEVER POSITION |
![]() |
Remove the nut and disconnect the control cable.
Remove the clip and disconnect the control cable from the control cable bracket.
![]() |
Push the control shaft rearward as much as possible.
Return the control shaft lever 2 notches to the N position.
While holding the control shaft lever slightly toward the R position side, tighten the nut.
| 23. ADD AUTOMATIC TRANSMISSION FLUID |
| 24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 25. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 26. INSPECT SHIFT LEVER POSITION |
When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.
Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after shifting to R.
If the results are not as specified, inspect the park/neutral position switch and check the shift lever.
| 27. INSTALL CONSOLE BOX ASSEMBLY |
![]() |
Install the console box with the 2 clips, 4 screws <F> and 2 bolts <E>.
| 28. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Attach the 12 claws to install the console panel.
| 29. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY |
![]() |
Attach the 4 claws to install the hole cover.
| 30. CHECK FOR EXHAUST GAS LEAKS |
| 31. INSPECT AUTOMATIC TRANSMISSION FLUID |
Inspect the automatic transmission fluid (Click here).
| 32. INSTALL NO. 2 ENGINE UNDER COVER |
| 33. INSTALL NO. 1 ENGINE UNDER COVER |