AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Inspect the torque converter clutch (Click here).
| 2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY |
![]() |
Install the torque converter clutch to the automatic transmission.
Using a vernier caliper and straightedge, measure dimension A between the contact surfaces of the transmission and engine (*1), and the contact surfaces of the converter and drive plate *2. (#)
![]() |
Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A measured in step (#).
| 3. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR |
![]() |
Install the engine mounting insulator to the transmission with the 4 bolts.
| 4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.
![]() |
Install the transmission to the engine with the 7 bolts.
![]() |
Install the exhaust manifold stay with the 3 bolts.
![]() |
Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch mounting bolts.
| 5. INSTALL FLYWHEEL HOUSING DUST SEAL |
| 6. CONNECT WIRE HARNESS |
| 7. CONNECT CONNECTOR |
Connect the connectors.
Connect the temperature sensor connector.
Connect the park/neutral position switch connector.
Connect the 3 speed sensor connectors.
Connect the transmission wire connector.
| 8. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
*1: Install the 4 set bolts of the engine mounting insulator.
*2: Install the frame crossmember with the 4 bolts and 4 nuts.
| 9. INSTALL STARTER ASSEMBLY |
| 10. INSTALL TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Install the control cable bracket with the 2 bolts.
| 11. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable with the clip.
Connect the control cable with the nut.
| 12. CONNECT OIL COOLER TUBE |
![]() |
Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.
Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.
Install the 3 clamps with the 3 bolts.
![]() |
Using union nut wrench, tighten the inlet and outlet tubes.
| 13. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY |
![]() |
Coat a new O-ring with ATF, and install it to the oil filler tube.
Install the oil filler tube with the 2 bolts.
Install the oil dipstick.
| 14. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
Install the propeller shaft with center bearing assembly (Click here).
| 15. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install the front exhaust pipe (Click here).
| 16. ADJUST SHIFT LEVER POSITION |
Move the shift lever to N.
![]() |
Remove the nut and disconnect the control cable.
![]() |
Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.
While holding the control shaft lever slightly toward the R position side, connect the cable with the nut.
| 17. INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Install the frame crossmember with the 4 bolts and 4 nuts.
| 18. ADD AUTOMATIC TRANSMISSION FLUID |
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 20. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 21. INSPECT SHIFT LEVER POSITION |
When moving the shift lever from P to R with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.
Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.
| 22. CHECK FOR EXHAUST GAS LEAKS |
| 23. INSPECT AUTOMATIC TRANSMISSION FLUID |
Inspect the automatic transmission fluid (Click here).