Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER WINDOW REGULATOR MASTER SWITCH (for LHD) (for Single cab, Extra cab)

B112770E01

  1. Disconnect the P4 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (P4-9) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (P4-9) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (P4-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 switch connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (P4-3) - E (P4-1)
    R - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-4) - E (P4-1)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-4) - E (P4-1)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).


CHECK POWER WINDOW REGULATOR MASTER SWITCH (for RHD) (for Single cab, Extra cab)

B112770E01

  1. Disconnect the P4 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (P4-9) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (P4-9) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (P4-10) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 switch connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (P4-2) - E (P4-10)
    B - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-5) - E (P4-10)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-5) - E (P4-10)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).


CHECK POWER WINDOW REGULATOR MASTER SWITCH (for LHD) (for Double cab)

B112771E01

  1. Disconnect the P4 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (P4-6) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (P4-6) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (P4-3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 switch connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (P4-4) - E (P4-3)
    R - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-9) - E (P4-3)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-9) - E (P4-3)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).


CHECK POWER WINDOW REGULATOR MASTER SWITCH (for RHD) (for Double cab)

B112771E01

  1. Disconnect the P4 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (P4-6) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (P4-6) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (P4-3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 switch connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (P4-4) - E (P4-3)
    B - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-9) - E (P4-3)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-9) - E (P4-3)
    L-R - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).


CHECK POWER WINDOW REGULATOR MASTER SWITCH (w/ Jam Protection)

B112771E29

  1. Disconnect the P4 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (P4-6) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (P4-6) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    BW (P4-7) - Body ground
    L-B - Body ground
    Regulator motor power supply
    Always
    10 to 14 V
    E (P4-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 switch connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (P4-4) - E (P4-1)
    R - W-B
    Driver side power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    U (P4-4) - E (P4-1)
    R - W-B
    Driver side power window motor UP output
    Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
    Below 1 V → 10 to 14 V → Below 1 V
    D (P4-9) - E (P4-1)
    L-R - W-B
    Driver side power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (P4-9) - E (P4-1)
    L-R - W-B
    Driver side power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    U (P4-13) - E (P4-1)
    R-L - W-B
    Front passenger side power window motor UP output
    1. Window lock switch OFF
    2. Ignition switch ON, front passenger side power window remote manual switch OFF → UP
    Below 1 V → 10 to 14 V
    D (P4-15) - E (P4-1)
    G-W - W-B
    Front passenger side power window motor DOWN output
    1. Window lock switch OFF
    2. Ignition switch ON, front passenger side power window remote manual switch OFF → DOWN
    Below 1 V → 10 to 14 V
    U (P4-12) - E (P4-1)
    R-Y - W-B
    Rear power window LH motor UP output
    1. Window lock switch OFF
    2. Ignition switch ON, rear power window LH remote manual switch OFF → UP
    Below 1 V → 10 to 14 V
    D (P4-10) - E (P4-1)
    G-Y - W-B
    Rear power window LH motor DOWN output
    1. Window lock switch OFF
    2. Ignition switch ON, rear power window LH remote manual switch OFF → DOWN
    Below 1 V → 10 to 14 V
    U (P4-18) - E (P4-1)
    R-B - W-B
    Rear power window RH motor UP output
    1. Window lock switch OFF
    2. Ignition switch ON, rear power window RH remote manual switch OFF → UP
    Below 1 V → 10 to 14 V
    D (P4-16) - E (P4-1)
    G-B - W-B
    Rear power window RH motor DOWN output
    1. Window lock switch OFF
    2. Ignition switch ON, rear power window RH remote manual switch OFF → DOWN
    Below 1 V → 10 to 14 V
    VCC (P4-3) - GND (P4-2)
    BR - L-O
    Power window motor sensor power source
    Ignition switch ON, driver side power window switch OFF → UP or DOWN
    Below 1 V → 10 to 14 V
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).