Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

If the rear RH side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B107968E63


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH) (POWER SOURCE)
B107969E06
  1. Disconnect the P11 regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P11-3 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH)
B063163
  1. Remove the switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 4
    2 - 3
    UP
    Below 1 Ω
    5 - 4
    2 - 1
    OFF
    Below 1 Ω
    5 - 3
    2 - 1
    DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH)
OK


3.CHECK WIRE HARNESS (SWITCH (REAR RH) - MOTOR (REAR RH))

B111942E04

  1. Disconnect the P11 switch connector.

  1. Disconnect the P8 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P11-5 - P8-1
    Below 1 Ω
    P11-2 - P8-2
    Below 1 Ω
    P11-5 or P8-1 - Body ground
    10 kΩ or higher
    P11-2 or P8-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)
B085064E01
  1. Remove the motor.

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - SWITCH (REAR RH))


  1. w/o Jam Protection


    B111937E52

    1. Disconnect the P4 master switch connector.

    2. Disconnect the P11 switch connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      for LHD:
      Tester Connection
      Specified Condition
      P4-10 (U) - P11-1
      Below 1 Ω
      P4-16 (D) - P11-4
      Below 1 Ω
      P4-10 (U) or P11-1 - Body ground
      10 kΩ or higher
      P4-16 (D) or P11-4 - Body ground
      10 kΩ or higher

      Standard resistance:
      for RHD:
      Tester Connection
      Specified Condition
      P4-16 (U) - P11-1
      Below 1 Ω
      P4-15 (D) - P11-4
      Below 1 Ω
      P4-16 (U) or P11-1 - Body ground
      10 kΩ or higher
      P4-15 (D) or P11-4 - Body ground
      10 kΩ or higher



  1. w/ Jam Protection


    B111937E55

    w/o Jam Protection
    1. Disconnect the P4 master switch connector.

    2. Disconnect the P11 switch connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      P4-18 (U) - P11-1
      Below 1 Ω
      P4-10 (D) - P11-4
      Below 1 Ω
      P4-18 (U) or P11-1 - Body ground
      10 kΩ or higher
      P4-10 (D) or P11-4 - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY