Home › SUSPENSION & AXLE › AXLE › STEERING KNUCKLE (for 4WD and Pre-Runner)

STEERING KNUCKLE (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT AXLE HUB ASSEMBLY


F042759E01
  1. Apply MP grease to a new O-ring.

  1. Install the new O-ring to the axle hub.

  1. Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



2. INSTALL FRONT AXLE HUB DUST SEAL (for 4WD)


F042767E01
  1. Using SST and a press, press in a new dust seal.

    SST
    09527-17011  
    09950-70010   (09951-07100)
    09951-01000  



3. INSTALL KNUCKLE GREASE RETAINER CAP LH (for Pre-Runner)


F042765E01
  1. Using a brass bar and hammer, install a new retainer cap.

    NOTICE:
    Do not damage the retainer cap.



4. CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY LH


F043605E01
  1. Connect the upper arm with the nut.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }

  1. Install a new clip.

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut an additional 60°.



5. CONNECT FRONT SUSPENSION LOWER ARM ASSEMBLY WITH ATTACHMENT LH


F050870E01
  1. Connect the suspension arm with the 2 bolts.

    Torque:
    160 N*m{ 1,632 kgf*cm , 118 ft.*lbf }



6. CONNECT TIE ROD END SUB-ASSEMBLY LH


C113718
  1. Connect the tie rod end with the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



7. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


C099158E01
  1. Connect the stabilizer link with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



8. INSTALL FRONT AXLE HUB NUT (for 4WD)


F042732E01
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



9. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
  1. Install a new grease cap to the axle hub.



10. INSTALL FRONT DISC


11. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH


F050211E01
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }



    F042731E01
  1. Install the brake tube bracket to the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F051151E01
  1. Using SST, connect the brake tube to the disc brake cylinder.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf } for use without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



12. INSTALL SPEED SENSOR FRONT LH


C113715
  1. Install the speed sensor with the bolt.

  1. Connect the 2 clamps.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Install the speed sensor wire harness to the steering knuckle with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



13. BLEED AIR FROM BRAKE LINE
  1. TMT made:
    Bleed air from the brake line (Click here).

  1. TSAM made LHD:
    Bleed air from the brake line .

  1. TSAM made RHD:
    Bleed air from the brake line .



14. CHECK BRAKE FLUID LEVEL IN RESERVOIR
  1. TMT made:
    Check the brake fluid level in the reservoir (Click here).

  1. TSAM made LHD:
    Check the brake fluid level in the reservoir .

  1. TSAM made RHD:
    Check the brake fluid level in the reservoir .



15. CHECK FOR BRAKE FLUID LEAKAGE
  1. TMT made:
    Check for brake fluid leakage (Click here).

  1. TSAM made LHD:
    Check for brake fluid leakage .

  1. TSAM made RHD:
    Check for brake fluid leakage .



16. INSTALL FRONT WHEEL

Torque:
105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }