Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Seat Belt Warning Light for Passenger Seat does not Flash

for Preparation Click here


WIRING DIAGRAM


E115294E09


E115294E10


INSPECTION PROCEDURE

1.INSPECT FUSE (ECU-IG & GAUGE)
  1. Remove the ECU-IG & GAUGE fuse from the instrument panel junction block (driver side junction block).

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK WIRE HARNESS (METER*1 OR LIGHT*2 - BATTERY AND GROUND)
E110289E05
  1. Disconnect the A27*1 meter connector.

  1. Disconnect the P13*2 light connector.

HINT:
*1: w/ Accessory meter
*2: w/o Accessory meter

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    w/ Accessory meter 
    Tester Connection
    Condition
    Specified Condition
    A27-12 (IG) - Body ground
    Ignition switch ON
    10 to 14 V
    Ignition switch OFF
    Below 1 V

    w/o Accessory meter:
    Tester Connection
    Condition
    Specified Condition
    P13-3 - Body ground
    Ignition switch ON
    10 to 14 V
    Ignition switch OFF
    Below 1 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    w/ Accessory meter  
    Tester Connection
    Specified Condition
    A27-1 (GND) - Body ground
    Below 1 Ω

    w/o Accessory meter:
    Tester Connection
    Specified Condition
    P13-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (BUCKLE SWITCH)
E111664E03
  1. Disconnect the F17 belt connector.

  1. Measure the resistance of the buckle switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt is unfastened (ON) and apply more than 147 N (15 kgf, 22 lbf) of force to occupant detection sensor
    Below 1 Ω
    Seat belt is fastened (OFF)
    1 MΩ or higher



NG
Go to step 6
OK


4.CHECK WIRE HARNESS (INNER BELT - BODY GROUND)
E117164E05
  1. Disconnect the F17 belt connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    F17-2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (INNER BELT - METER*1 OR LIGHT*2)

E117529E03

  1. Disconnect the F17 belt connector.

  1. Disconnect the A27*1 meter connector.

  1. Disconnect the P13*2 light connector.

HINT:
*1: w/ Accessory meter
*2: w/o Accessory meter

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    w/ Accessory meter 
    Tester Connection
    Specified Condition
    F17-1 - A27-8 (PBEW)
    Below 1 Ω

    w/o Accessory meter:
    Tester Connection
    Specified Condition
    F17-1 - P13-3
    Below 1 Ω

Result:
Result
Proceed to
OK (w/ Accessory meter assembly)
A
OK (w/o Accessory meter assembly)
B
NG
C



B
REPLACE PASSENGER SEAT BELT WARNING LIGHT

C
REPAIR OR REPLACE HARNESS AND CONNECTOR
A

REPLACE ACCESSORY METER ASSEMBLY (MULTI-DISPLAY) 

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY (OCCUPANT DETECTION SENSOR)
E076458E04
  1. Disconnect the A sensor connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Apply more than 147 N (15 kgf, 22 lbf) of force to occupant detection sensor
    Below 100 Ω
    No force applied to occupant detection sensor
    1 MΩ or higher



NG
REPAIR FRONT SEAT CUSHION PAD
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR PASSENGER SIDE)