Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › CONDENSER (for TR Series Engine)

CONDENSER (for TR Series Engine) > INSTALLATION

for Preparation Click here



1. INSTALL COOLER CONDENSER ASSEMBLY


    E112001
  1. Install the cooler condenser.



2. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER


    E111649E01
  1. Install the radiator support with the 6 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for bolt A

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf } for bolt B



3. INSTALL HOOD LOCK ASSEMBLY


I043247E01
  1. Install the hood lock with the 3 bolts.



4. INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY


I043738E01
  1. Remove the vinyl tape attached to the pipe and connecting part of the cooler condenser.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the A/C tube.

  1. Install the A/C tube on the cooler condenser with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



5. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


I043737E01
  1. Remove the vinyl tape attached to the pipe and connecting part of the cooler condenser.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the refrigerant discharge hose.

  1. Install the refrigerant discharge hose on the cooler condenser with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



6. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


B085202E01
  1. Install the reinforcement with the 4 nuts.

    Torque:
    67 N*m{ 683 kgf*cm , 49 ft.*lbf }



7. INSTALL FRONT BUMPER COVER
  1. w/ Fog light:
    Connect the 2 fog light connectors.



    B085206E01
  1. Put protective tape under the front fender.

  1. Attach the 4 claws to install the cover.



    B085205E01
  1. Install the 9 clips.



8. INSTALL RADIATOR GRILLE


B108604E01
  1. Push the radiator grille in the direction indicated by the arrow in the illustration. Attach the 5 claws to install the radiator grille.

  1. Install the 2 screws and 2 clips.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


10. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



11. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    450 +- 30 g (15.87 +- 1.05 oz.)



    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    1. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.



12. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

    NOTICE:
    After removing and installing the cooler refrigerant lines (with the compressor), be sure to warm up the compressor when turning the A/C switch ON. This is done to prevent damage to the compressor.



13. CHECK FOR LEAKAGE OF REFRIGERANT
  1. After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.

    1. The ignition switch is OFF.
    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases. If volatile gases are unavoidable, the vehicle must be lifted up.
    3. Some refrigerant is remaining in the refrigerant system.
    4. The compressor is OFF and its pressure is approximately 392 to 588 kPa (4 to 6 kgf/cm2).



    I042222E03
  1. Check for refrigerant gas leakage from the refrigerant line.

    1. After the blower motor stops, wait at least 15 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the refrigerant line. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Hold the gas leak detector so that the sensor is under the drain hose, as shown in the illustration.

    2. Check that gas is not leaking from the drain hose. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Remove the blower motor control from the unit. Insert the gas leak detector's sensor into the unit.

    2. Check that gas is not leaking from the unit. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the pressure switch.

    1. Disconnect the pressure switch connector and wait approximately 20 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the pressure switch. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Repeat all steps above 2 to 3 times.