Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0335    Crankshaft Position Sensor "A" Circuit Malfunction

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the common rail system is controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
When either condition below is met:
  1. No crankshaft position sensor signal to ECM while cranking (1 trip detection logic)
  2. No crankshaft position sensor signal to ECM with engine speed 600 rpm or more (1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 1 crankshaft position sensor plate
  4. ECM
P0339
No crankshaft position sensor signal to ECM is input for 0.05 seconds or more, and conditions 1, 2 and 3 are met
(1 trip detection logic):
  1. Engine is at 1,000 rpm or more
  2. STA signal is OFF
  3. 3 seconds or more have elapsed after STA signal is switched from ON to OFF
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 1 crankshaft position sensor plate
  4. ECM
Reference: Inspection using the oscilloscope.
While idling, the correct waveform is shown in the diagram.
A098437E04

HINT:
G stands for the camshaft position sensor signal, and NE stands for the crankshaft position sensor signal.
Item
Content
Terminal
(a) NE+ - NE-
Tester Range
5V/DIV., 20 msec./DIV.
Condition
Cranking or idling


WIRING DIAGRAM


A154730E02


INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If no trouble is found in the diagnostic troubleshooting procedure of DTC P0335, troubleshoot the engine mechanical system.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
A072395E16
  1. Disconnect the C4 sensor connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Approx. 20°C (68°F)
    1,850 to 2,450 Ω



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A099852E16
  1. Disconnect the C4 sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    C4-1 (NE+) - E8-27 (NE+)
    Below 1 Ω
    C4-2 (NE-) - E8-34 (NE-)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    C4-1 (NE+) or E8-27 (NE+) - Body ground
    10 kΩ or higher
    C4-2 (NE-) or E8-34 (NE-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CRANKSHAFT POSITION SENSOR (INSTALLATION)
BR03795E25
  1. Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
OK


4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Check the teeth of the crankshaft position sensor No. 1 plate.

    OK:
    The sensor plate's teeth do not have any cracks or deformation.



NG
REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
OK

REPLACE ECM