Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

ECD SYSTEM (w/ EGR Cooler) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the intelligent tester ON.



  6. A114778E02
  7. Enter the following menus: Powertrain / Engine / Data List.

    HINT:
    To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.

  8. Read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    10 to 40%: Idling
    10 to 40%: Running without load
    (2,500 rpm)
    -
    MAP
    Absolute pressure inside intake manifold/
    Min.: 0 kPa, Max.: 255 kPa
    1. 90 to 100 kPa: Idling
    2. 90 to 110 kPa:
      Engine running at 2,000 rpm
    3. 110 to 130 kPa:
      Engine running at 3,000 rpm
    -
    MAF
    Air flow rate from Mass Air Flow (MAF) sensor/
    Min.: 0 gm/sec., Max.: 655.35 gm/sec.
    5 to 12 gm/s: Idling
    0 gm/s: MAF sensor power source circuit shorted
    180 gm/s or more: E2G circuit is open
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16,383.75 rpm
    700 to 800 rpm: Idling
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    80 to 95°C (176 to 203°F):
    After warming up engine
    If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to temperature at location of mass air flow meter
    If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Fuel Press
    Fuel pressure/
    Min.: 0 MPa, Max.: 655.350 MPa
    25 to 35 MPa: Idling
    -
    Accelerator Position No. 1
    Accelerator pedal position No. 1/
    Min.: 0%, Max.: 100%
    1. Accelerator pedal released:
      8 to 28%
    2. Accelerator pedal depressed:
      51 to 71%
    Read value with ignition switch ON (do not start engine)
    Accelerator Position No. 2
    Accelerator pedal position No. 2/
    Min.: 0%, Max.: 100%
    1. Accelerator pedal released:
      30 to 55%
    2. Accelerator pedal depressed:
      73 to 98%
    Read value with ignition switch ON (do not start engine)
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    ECT when engine starts
    -
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    IAT when engine starts
    -
    Intake Air Temp (Turbo)
    Diesel turbo intake air temperature:
    Min.: -40°C, Max.: 190°C
    -
    If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
    Throttle Valve Fully Closed
    Throttle valve fully closed
    0.645 to 0.775 V
    -
    EGR Position
    EGR position/
    Min.: 0%, Max.: 100%
    Level surface, engine warmed up and engine idling:
    50 to 100%
    -
    EGR Lift Position
    EGR lift position:
    Min.: 0%, Max.: 100%
    70 to 90 %: Idling
    -
    EGR Close Learning Value
    EGR close learning value/
    Min.: 0 V, Max.: 5 V
    Level surface, room temperature, engine warmed up and engine idling:
    0.15 to 1.45 V
    -
    Diesel Throttle Learn Status
    Diesel throttle learn status:
    OK or NG
    OK
    -
    Target Common Rail Pressure
    Target common rail pressure/
    Min.: 0 kPa, Max.: 655,350 kPa
    20,000 to 160,000 kPa
    -
    VNT Type
    VNT type:
    0: Not, 1: Commo, 2: Vacumm
    0: Not
    -
    Injection Pressure Correction
    Injection pressure correction/
    Min.: -500 mm3/st,
    Max.: 780 mm3/st
    -400 to 400 mm3/st
    -
    Alternate Duty Ratio
    Alternate duty ratio/
    Min.: 0%, Max.: 100%
    1. No electrical load:
      20 to 60%
    1. High electrical load:
      100%
    -
    Fuel Temperature
    Fuel temperature:
    Min.: -40°C, Max.: 140°C
    Actual fuel temperature
    ECD freeze frame data
    Accel Position 1
    Accelerator pedal position sensor No. 1 voltage/
    Min.: 0 V, Max.: 5 V
    1. Accelerator pedal released:
      0.5 to 1.1 V
    2. Accelerator pedal depressed:
      2.6 to 4.5 V
    Read value with ignition switch ON (do not start engine)
    Accel Position 2
    Accelerator pedal position sensor No. 2 voltage/
    Min.: 0 V, Max.: 5 V
    1. Accelerator pedal released:
      1.2 to 2.0 V
    2. Accelerator pedal depressed:
      3.4 to 5.0 V
    Read value with ignition switch ON (do not start engine)
    Accel Position
    Accelerator pedal position status/
    Min.: 0%, Max.: 100%
    1. Accelerator pedal released:
      10 to 22%
    2. Accelerator pedal depressed:
      52 to 90%
    Read value with ignition switch ON (do not start engine)
    Pump VCM Angle
    Pump VCM angle/
    Min.: 0 mA, Max.: 4,000 mA
    -
    ECD freeze frame data
    IDL Stable Control
    IDL stable control/
    Min.: -80 mm3/st, Max.: 79 mm3/st
    -10 to 10 mm3/st
    ECD freeze frame data
    Pilot 1 Injection
    Pilot 1 injection/
    Min.: 0 μs, Max.: 65,535 μs
    -
    -
    Pilot 2 Injection
    Pilot 2 injection/
    Min.: 0 μs, Max.: 65,535 μs
    450 to 550 μs: Idling
    -
    Main Injection
    Main injection/
    Min.: 0 μs, Max.: 65,535 μs
    525 to 675 μs: Idling
    -
    After Injection
    After injection/
    Min.: 0 μs, Max.: 65,535 μs
    -
    -
    Pilot 1 Injection
    Pilot 1 injection/
    Min.: -70°CA, Max.: 20°CA
    -
    -
    Pilot 2 Injection
    Pilot 2 injection/
    Min.: -50°CA, Max.: 20°CA
    -15°CA: Idling
    -
    Main Injection
    Main injection/
    Min.: -90°CA, Max.: 90°CA
    5.8°CA: Idling
    -
    After Injection
    After injection/
    Min.: -10°CA, Max.: 50°CA
    -
    -
    Injection Feedback Value
    Injection volume feedback learning value/
    Min.: -10 mm3, Max.: 9.92 mm3
    -4.0 to 4.0 mm3: Idling
    -
    Injection Feedback Val #1
    Injection volume correction for cylinder 1/
    Min.: -10 mm3, Max.: 10 mm3
    -3.0 to 3.0 mm3: Idling
    -
    Injection Feedback Val #2
    Injection volume correction for cylinder 2/
    Min.: -10 mm3, Max.: 10 mm3
    -3.0 to 3.0 mm3: Idling
    -
    Injection Feedback Val #3
    Injection volume correction for cylinder 3/
    Min.: -10 mm3, Max.: 10 mm3
    -3.0 to 3.0 mm3: Idling
    -
    Injection Feedback Val #4
    Injection volume correction for cylinder 4/
    Min.: -10 mm3, Max.: 10 mm3
    -3.0 to 3.0 mm3: Idling
    -
    Injection Volume
    Injection volume/
    Min.: 0 mm3, Max.: 1,279.98 mm3
    3 to 10 mm3: Idling
    -
    Diesel Throttle Angle
    Diesel throttle angle:
    Min.: -20%, Max.: 120%
    70 to 80 %:
    Idling after engine warmed-up
    -
    EGR Learning Status
    EGR learning status/
    OK or NG
    OK
    -
    Model Code
    Model code
    -
    -
    Engine Type
    Engine type
    -
    -
    Cylinder Number
    Cylinder number:
    0 to 255
    -
    -
    -
    Destination
    Destination
    -
    -
    Model Year
    Model year
    1900 to 2155
    -
    -
    System Identification
    System identification
    -
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    A/C Signal
    A/C signal/
    ON or OFF
    ON: A/C ON
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    1. ON: Brake pedal depressed
    2. OFF: Brake pedal released
    -
    Battery Voltage
    Battery voltage/
    Min.: 0 V
    Max.: 65.535 V
    9 to 14 V: Idling
    -
    Atmosphere Pressure
    Atmospheric pressure value/
    Min.: 0 kPa (0 mmHg, 0 in.Hg),
    Max.: 255 kPa (1,912.6 mmHg, 75.3 in.Hg)
    Actual atmospheric pressure
    -
    Swirl Control Valve VSV
    VSV for No. 1 Swirl control valve status:
    ON or OFF
    ON: Idling
    -
    EGR
    EGR status for Active Test/
    ON or OFF
    -
    Active Test support data
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    Active Test support data
    TC and TE1
    TC and TE1 terminal of DLC3:
    ON or OFF
    -
    -
    #Code
    #Code/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    -
    SPD Test
    Check mode result for vehicle speed sensor/
    0: COMPL, 1: INCOMPL
    -
    Click here
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km
    Max.: 65,535 km
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 minutes
    Max.: 65,535 minutes
    Equivalent running time after MIL was ON
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km
    Max.: 65,535 km
    Equivalent to drive distance after DTCs were erased
    -
    Warmup Cycle Cleared DTC
    Warm up cycles after DTC cleared/
    Min.: 0
    Max.: 255
    -
    Number of warm up cycles after DTC cleared
    Engine Run Time
    Engine run time/
    Min.: 0 seconds
    Max.: 65,535 seconds
    Time after engine started
    Service data
    Time After DTC Cleared
    Time after DTC cleared/
    Min.: 0 minutes
    Max.: 65,535 minutes
    Equivalent to time after DTCs were erased
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power input ON or OFF
    ON: Idling
    -
    Throttle Motor
    Throttle motor:
    ON or OFF
    ON: Idling
    -
    Actuator Power Supply
    Actuator power supply
    ON or OFF
    ON: Idling
    -

    HINT:
    Normal Condition: If no idling conditions are specified, the shift lever is in the N position, and the A/C switch and all accessory switches are OFF.


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the intelligent tester ON.

  4. Enter the following menus: Powertrain / Engine / Active Test.

  5. Perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the VSV for Swirl Control Valve
    Activate VSV for swirl control valve
    ON/OFF
    -
    Activate the VSV for EGR Cut
    Activate VSV for EGR Cut
    ON/OFF
    -
    Control the EGR System
    Activate E-VRV for E-EGR
    ON/OFF
    -
    Control the A/C cut Signal
    Control the A/C signal
    ON/OFF
    -
    Connect the TC and TE1
    Turn on TC and TE1 connection
    ON/OFF
    -
    Control the Cylinder#1 Fuel Cut
    Cut off fuel injection from No. 1 injector
    ON/OFF
    Fuel injection stopped while test is ON
    Control the Cylinder#2 Fuel Cut
    Cut off fuel injection from No. 2 injector
    ON/OFF
    As above
    Control the Cylinder#3 Fuel Cut
    Cut off fuel injection from No. 3 injector
    ON/OFF
    As above
    Control the Cylinder#4 Fuel Cut
    Cut off fuel injection from No. 4 injector
    ON/OFF
    As above
    Test the Fuel Leak
    Pressurizes common rail internal fuel pressure, and checks for fuel leaks
    Stop/Start
    1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
    2. Above conditions preserved while test is ON