Home › TRANSMISSION · A340F AUTOMATIC TRANSMISSION › ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM

DTC    U0100/A2    Lost Communication with ECM/PCM "A"

for Preparation Click here


DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine rpm, required engine torques, warning indicators in the combination meter, DTCs and other data. The ECM sends signals to the TCM concerning engine rpm, opening angles of the throttle valve, temperature of the intake air and engine coolant, engine torques, and other data.
If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and set a DTC.

DTC No.
DTC Detection Condition
Trouble Area
U0100/A2
No communication from ECM continues
  1. Open or short in TCM and ECM circuit
  2. TCM
  3. ECM

WIRING DIAGRAM


C193770E05


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
If the ECM is replaced, the new ECM needs initialization.

1.CHECK ECM (VC, +B VOLTAGE, E1 GROUND)
C192331E18
  1. Measure the voltage and resistance of the ECM connectors.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E5-1 (+B) - Body ground
    Ignition switch ON
    9 to 14 V
    E8-18 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-7 (E1) - Body ground
    Always
    Below 1 Ω



NG
INSPECT +B, E1 CIRCUIT (ECM POWER SOURCE CIRCUIT OR VC CIRCUIT)
OK


2.CHECK TCM (IG2 VOLTAGE, E1 GROUND)
C191543E12
  1. Measure the voltage and resistance of the TCM connectors.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T17-6 (IG2) - Body ground
    Ignition switch ON
    9 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-1 (E1) - Body ground
    Always
    Below 1 Ω



NG
INSPECT IG2, E1 CIRCUIT (TCM POWER SOURCE CIRCUIT)
OK


3.CHECK WIRE HARNESS (ECM - TCM)
C193771E05
  1. Disconnect the E6 ECM connector.

  1. Disconnect the T17 TCM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-22 (CAN+) - T17-21 (CAN+)
    Always
    Below 1 Ω
    E6-21 (CAN-) - T17-20 (CAN-)
    Always
    Below 1 Ω
    E6-22 (CAN+) or T17-21 (CAN+) - Body ground
    Always
    10 kΩ or higher
    E6-21 (CAN-) or T17-20 (CAN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CONFIRM DTC
  1. Clear the DTC.

  1. Replace the TCM.

    HINT:
    Replace the TCM with a TCM from a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    U0100/A2 is output
    A
    U0100/A2 is not output
    B



B
REPLACE TCM
A

REPLACE ECM