AUTOMATIC TRANSMISSION UNIT > INSPECTION |
| 1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
![]() |
Remove the magnets, and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.
| 2. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the reverse clutch hub and turn the 1-way clutch assembly.
Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.
| 3. INSPECT REAR CLUTCH DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 4. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.
| 5. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the forward clutch hub bush.
| 6. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 7. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 8. INSPECT DIRECT CLUTCH DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 9. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 10. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 11. INSPECT NO. 3 BRAKE DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 12. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 13. INSPECT FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the front planetary pinion gear thrust clearance.
![]() |
Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.
| 14. INSPECT 1-WAY CLUTCH ASSEMBLY |
![]() |
Install the 1-way clutch to the 1-way clutch inner race.
Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
Remove the 1-way clutch from the 1-way clutch inner race.
| 15. INSPECT NO. 1 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 16. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 17. INSPECT NO. 2 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 18. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 19. INSPECT CENTER PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the center planetary pinion gear thrust clearance.
| 20. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
| 21. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.
| 22. INSPECT INTERMEDIATE SHAFT |
![]() |
Using a dial indicator, measure the intermediate shaft runout.
![]() |
Using a micrometer, measure the diameter of the intermediate shaft at the positions shown in the diagram.
| 23. INSPECT NO. 4 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 24. INSPECT REAR PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the rear planetary pinion gear thrust clearance.
![]() |
Using a dial indicator, measure the inside diameter of the rear planetary gear bush.
| 25. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 26. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE |
![]() |
Make sure the 1st and reverse brake piston moves smoothly when applying and releasing compressed air into the transmission case.
| 27. INSPECT PISTON STROKE OF NO. 1 BRAKE PISTON |
![]() |
Make sure the No. 1 brake piston moves smoothly when applying and releasing compressed air into the transmission case.
![]() |
Using a feeler gauge, measure the B3 bearing pack clearance between the snap ring and flange.
| 28. INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
![]() |
Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while applying air to the oil hole as shown in the illustration, and calculate the average.
| Mark | Thickness |
| 2 | 2.95 to 3.05 mm (0.116 to 0.120 in.) |
| 3 | 3.05 to 3.15 mm (0.120 to 0.124 in.) |
| 4 | 3.15 to 3.25 mm (0.124 to 0.128 in.) |
| 5 | 3.25 to 3.35 mm (0.128 to 0.132 in.) |
| 6 | 3.35 to 3.45 mm (0.132 to 0.136 in.) |
| 7 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 8 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 9 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| A | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| 29. INSPECT PACK CLEARANCE OF REVERSE CLUTCH |

Using a dial indicator, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse flange at both ends across a diameter while applying air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole as shown in the illustration, and calculate the average.
| Mark | Thickness |
| 0 | 2.75 to 2.85 mm (0.108 to 0.112 in.) |
| 1 | 2.85 to 2.95 mm (0.112 to 0.116 in.) |
| 2 | 2.95 to 3.05 mm (0.116 to 0.120 in.) |
| 3 | 3.05 to 3.15 mm (0.120 to 0.124 in.) |
| 4 | 3.15 to 3.25 mm (0.124 to 0.128 in.) |
| 5 | 3.25 to 3.35 mm (0.128 to 0.132 in.) |
| 6 | 3.35 to 3.45 mm (0.132 to 0.136 in.) |
| 7 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 8 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 9 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| A | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| 30. INSPECT PACK CLEARANCE OF FORWARD CLUTCH |
![]() |
Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while applying air to the oil hole as shown in the illustration, and calculate the average.
| Mark | Thickness |
| 0 | 2.95 to 3.05 mm (0.116 to 0.120 in.) |
| 1 | 3.05 to 3.15 mm (0.120 to 0.124 in.) |
| 2 | 3.15 to 3.25 mm (0.124 to 0.128 in.) |
| 3 | 3.25 to 3.35 mm (0.128 to 0.132 in.) |
| 4 | 3.35 to 3.45 mm (0.132 to 0.136 in.) |
| 5 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 6 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 7 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| 8 | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| 9 | 3.85 to 3.95 mm (0.148 to 0.152 in.) |
| A | 3.95 to 4.05 mm (0.152 to 0.159 in.) |
| 31. INSPECT INDIVIDUAL PISTON OPERATION |
![]() |
Check the operating sound while applying compressed air into the oil holes indicated in the illustration.