Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 1KD-FTV)

AUTOMATIC TRANSMISSION ASSEMBLY (for 1KD-FTV) > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch assembly (Click here).



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


C187503E01
  1. Install the torque converter clutch to the automatic transmission.

  1. Using a vernier caliper measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)



    C193531E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A measured in the step labeled (#).

    Standard:
    B = A + 1.00 mm (0.0394 in.) or more



3. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer assembly (Click here).



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C187504E01
  1. Apply clutch spline grease to the round of the crankshaft contact surface with the torque converter clutch centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.353 oz)



    C196680
  1. Install the transmission to the engine with the 5 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }

    NOTICE:
    Confirm 2 knock pins are on the transmission fitting surface of the engine block before the transmission installation.



    G034258E01
  1. Turn the crankshaft to gain access to the installation locations of the 6 torque converter clutch mounting bolts and install each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then the remaining 5 bolts.



5. INSTALL STIFFENER PLATE


C187502E01
  1. Install the No. 2 end plate.

  1. Install the No. 4 cylinder block insulator.

  1. Install the stiffener plate LH to the engine and transmission with the 4 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }

  1. Install the stiffener plate RH (with oil cooler tube clamp) to the engine and transmission with the 4 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }



6. INSTALL STARTER ASSEMBLY

HINT:
Refer to "1KD-FTV STARTING-STARTER-INSTALLATION" and install the starter.



7. CONNECT WIRE HARNESS


8. CONNECT CONNECTOR
  1. Transmission side:
    Connect the connectors.

    1. Connect the park/neutral position switch connector.

    2. Connect the transmission wire connector.

    3. Connect the 2 speed sensor connectors.

  1. Transfer side:
    Connect the connectors.

    1. Connect the No. 1 indicator switch connector.

    2. Connect the No. 2 indicator switch connector.

    3. Connect the speed sensor connector.



9. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G034260E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



10. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256E01
  1. *1: Install the frame crossmember to the engine mounting insulator with the 4 set bolts.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. *2: Connect the ends of the frame crossmember to the vehicle with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



11. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


C111232
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C111231
  1. Connect the control cable with the clip and nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



13. CONNECT OIL COOLER TUBE


C187500E01
  1. Connect the end of the oil cooler tube inlet to the automatic transmission by hand.

  1. Connect the end of the oil cooler tube outlet to the automatic transmission by hand.

  1. Install the 3 clamps with the 3 bolts.

    Torque:
    for bolt A and B:
    5.0 N*m{ 50 kgf*cm , 43 in.*lbf }
    for bolt C:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C193850
  1. Using a union nut wrench, tighten the inlet and outlet tubes.

    Torque:
    without union nut wrench:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }
    with union nut wrench:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.



14. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
  1. Install the propeller shaft with center bearing assembly (Click here).



15. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the exhaust pipe (Click here).



16. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the protector with the 4 bolts.

    Torque:
    18 N*m{ 283 kgf*cm , 13 ft.*lbf }



17. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E02
  1. Install the transfer shift lever to the shift lever retainer.

  1. Using needle-nose pliers, install the snap ring.

  1. Install the transfer high and low shift lever with the 4 bolts.

    Torque:
    18 N*m{ 283 kgf*cm , 13 ft.*lbf }



18. INSTALL SHIFT LEVER BOOT ASSEMBLY
  1. Install the shift lever boot with the 4 screws.



19. INSTALL CONSOLE BOX ASSEMBLY
  1. Install the console box assembly (Click here).



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



21. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).



22. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
    If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.



23. PERFORM INITIALIZATION
  1. Perform initialization (Click here).



24. CHECK FOR EXHAUST GAS LEAK


25. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }



26. INSTALL NO .1 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }