Home › ENGINE ยท 2KD-FTV › INTAKE › TURBOCHARGER (w/ EGR Cooler)

TURBOCHARGER (w/ EGR Cooler) > INSTALLATION

for Preparation Click here



1. CLEAN TURBOCHARGER SUB-ASSEMBLY


2. INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY (for Motor Controlled Actuator)


    A211906E01
  1. Install a new gasket and the No. 1 turbo water pipe with the 2 nuts and bolt.

    Torque:
    for bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSTALL TURBOCHARGER SUB-ASSEMBLY (for Vacuum Controlled Actuator)


    A148152
  1. Temporarily install a new gasket and the turbocharger with 3 new nuts.

    HINT:
    It is easier to install the turbo oil inlet pipe if the 3 nuts are only loosely installed.



    A148153E02
  1. Temporarily install the turbo oil pipe.

    HINT:
    Before installing the oil pipe, clean it.


    1. Install a new gasket and the oil pipe with the 2 nuts, but only loosely install the nuts.

      NOTICE:
      The notch (wide part) of the gasket must face the engine.

    2. Install a new gasket and the oil pipe with the 2 bolts, but only loosely install the bolts.

      NOTICE:
      The claws of the gasket must face the pipe.

    3. Install a new gasket and the oil pipe with the union bolt, but only loosely install the union bolt.



    4. A148176
    5. Temporarily install the turbocharger stay with the 2 bolts and nut.

  1. Tighten the 3 nuts of the turbocharger.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Tighten the 2 nuts and 2 bolts of the turbo oil inlet pipe, and the union bolt.

    Torque:
    for bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for nut:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for union bolt:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Tighten the 2 bolts and nut of the turbocharger stay.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



4. INSTALL TURBOCHARGER SUB-ASSEMBLY (for Motor Controlled Actuator)


    A211839
  1. Temporarily install a new gasket and the turbocharger with 3 new nuts.

    HINT:
    It is easier to install the turbo oil inlet pipe if the 3 nuts are only loosely installed.



  1. Temporarily install the turbo oil inlet pipe.

    HINT:
    Before installing the oil inlet pipe, clean it.


    1. Install a new gasket and the oil inlet pipe with the 2 nuts, but only loosely install the nuts.

      NOTICE:
      The notch (wide part) of the gasket must face the engine.

    2. Install a new gasket and the oil inlet pipe with the 2 bolts, but only loosely install the bolts.

      NOTICE:
      The claws of the gasket must face the pipe.



    3. Install a new gasket and the oil inlet pipe with the union bolt, but only loosely install the union bolt.


      A211842E01



    4. A211837
    5. Temporarily install the turbocharger stay with the 2 bolts and nut.

  1. Tighten the 3 nuts of the turbocharger.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Tighten the 2 nuts labeled A.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the union bolt labeled B.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Tighten the 2 bolts labeled C.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A211837E01
  1. Tighten the 2 bolts and nut of the turbocharger stay in the order shown in the illustration.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



5. INSTALL TURBINE OUTLET ELBOW


    A148149
  1. for Vacuum Controlled Actuator:
    Install a new gasket and the turbine outlet elbow with the 4 nuts.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



    A211836
  1. for Motor Controlled Actuator:
    Install a new gasket and the turbine outlet elbow with the 3 nuts.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



6. INSTALL NO. 1 TURBO WATER HOSE (for Motor Controlled Actuator)


    A211835
  1. Install the 2 No. 1 turbo water hoses.



7. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (for Vacuum Controlled Actuator)


    A148148
  1. Install the No. 1 exhaust manifold heat insulator with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (for Motor Controlled Actuator)


    A211834
  1. Temporarily install the No. 1 exhaust manifold heat insulator with the bolt.



9. INSTALL NO. 1 TURBO INSULATOR (for Motor Controlled Actuator)
  1. Temporarily install the No. 1 turbo insulator with the 2 bolts.

  1. Tighten the bolt of the No. 1 exhaust manifold heat insulator, and the 2 bolts of the No. 1 turbo insulator.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



10. INSTALL COMPRESSOR INLET ELBOW


  1. for Vacuum Controlled Actuator:



      A148154E01
    1. Install the air cleaner hose and air cleaner hose No. 3 with the clamp labeled A as shown in the illustration.

      HINT:
      Align the protrusion of the turbocharger and the protrusion of the hose.

    2. for Ventilation Pipe Type:
      Install the inlet elbow with the clamp labeled B as shown in the illustration.

      HINT:
      Align the protrusion of the compressor inlet elbow and the protrusion of the hose.



    3. A148155
    4. for Ventilation Pipe Type:
      Connect the ventilation hose to the inlet elbow and cylinder head cover. Then move the clamp to the joint part of the hose.

    5. for Ventilation Pipe Type:
      Install the ventilation pipe with the bolt.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }



  1. for Motor Controlled Actuator:



      A211833
    1. Install a new gasket and the compressor inlet elbow with the 2 nuts.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    2. Connect the 2 connectors to the turbocharger.

    3. Attach the wire harness clamp.



    4. A211832
    5. for Ventilation Pipe Type:
      Connect the 2 ventilation hoses and install the ventilation pipe to the cylinder head cover with the bolt.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }



11. INSTALL INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
  1. Install the intake air connector to the air hoses.



    A135919
  1. Install the intercooler with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A135918
  1. Tighten the 2 clamps.



    A149802
  1. Connect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. Connect the vacuum hose to the manifold absolute pressure sensor.

  1. Attach the 2 clamps.



12. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY


A135916
  1. Install the engine cover with the 3 bolts and 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



13. INSTALL AIR CLEANER ASSEMBLY


    A099628E02
  1. Connect the air cleaner hose.

  1. for Ventilation Hose Type:
    Connect the Ventilation hose.

  1. Install the air cleaner with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Tighten the hose clamp of the compressor inlet elbow.

  1. Connect the MAF meter connector and attach the wire harness clamp.



14. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A111834
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the free length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A111803E01
  1. Install a new gasket to the outlet pipe.

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    1. Do not reuse the gasket.
    1. To ensure a proper seal, do not use the front pipe to force the gasket onto the outlet pipe.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and outlet pipe are properly fit.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    CAUTION:
    Do not reuse the gasket.



15. INSTALL FRONT FENDER SEAL
  1. Install the front fender seal with the 5 clips.



16. INSTALL FRONT FENDER APRON SEAL UPPER
  1. for 2WD:
    Install the front fender apron seal upper with the 6 clips.

  1. for 4WD:
    Install the front fender apron seal upper with the 5 clips.



17. INSTALL FRONT WHEEL RH


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



19. ADD ENGINE COOLANT (for Motor Controlled Actuator)
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A098989E01
  1. Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

    Standard capacity:
    9.8 liters (10.4 US qts, 8.6 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.



    A099591E01
  1. Using a wrench, install the vent plug.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    4. Stop the engine and wait until the coolant cools down to ambient temperature.

      CAUTION:
      Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    G036768E01
  1. After the coolant cools down, check that the coolant level is at the F line.
    If the coolant level is below the F line, add TOYOTA SLLC to the F line.



20. INSPECT FOR ENGINE COOLANT LEAK (for Motor Controlled Actuator)

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A097645E01
  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2 ,17.1 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks.
    If no external leaks are found, check the cylinder block and head.



21. INSPECT FOR OIL LEAK


22. INSPECT FOR EXHAUST GAS LEAK