THERMOSTAT (w/ EGR Cooler) > INSTALLATION |
| 1. INSTALL THERMOSTAT |
![]() |
Install a new gasket to the thermostat.
Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.
| 2. INSTALL WATER INLET |
![]() |
Install the water inlet with the 3 bolts.
| 3. INSTALL COMPRESSOR INLET ELBOW |
for Vacuum Controlled Actuator:
![]() |
Install the air cleaner hose and air cleaner hose No. 3 with the clamp labeled A as shown in the illustration.
for Ventilation Pipe Type:
Install the inlet elbow with the clamp labeled B as shown in the illustration.
![]() |
for Ventilation Pipe Type:
Connect the ventilation hose to the inlet elbow and cylinder head cover. Then move the clamp to the joint part of the hose.
for Ventilation Pipe Type:
Install the ventilation pipe with the bolt.
for Motor Controlled Actuator:
![]() |
Install a new gasket and the compressor inlet elbow with the 2 nuts.
Connect the 2 connectors to the turbocharger.
Attach the wire harness clamp.
![]() |
for Ventilation Pipe Type:
Connect the 2 ventilation hoses and install the ventilation pipe to the cylinder head cover with the bolt.
| 4. CONNECT RADIATOR HOSE INLET |
| 5. INSTALL INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR |
Install the intake air connector to the air hoses.
![]() |
Install the intercooler with the 4 bolts.
![]() |
Tighten the 2 clamps.
![]() |
Connect the IAT sensor connector and manifold absolute diesel pressure sensor connector.
Connect the vacuum hose to the manifold absolute pressure sensor.
Attach the 2 clamps.
| 6. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Install the engine cover with the 3 bolts and 2 nuts.
| 7. INSTALL AIR CLEANER ASSEMBLY |
Install the cleaner with the 2 bolts.
w/ Intake Air Temperature Sensor:
Connect the connector to the intake air temperature sensor.
w/ Mass Air Flow Meter:
Connect the connector to the mass air flow meter.
Tighten the hose clamp.
for Ventilation Hose Type:
Connect the ventilation hose.
| 8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 9. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 10. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2 ,17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 11. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD) |
Install the under cover with the 4 bolts.
| 12. PERFORM INITIALIZATION |
Perform initialization (Click here).