Home › BODY › INTERIOR › ROOF HEADLINING (for Single Cab)

ROOF HEADLINING (for Single Cab) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 SIDE RAIL SPACER REAR LH


2. INSTALL NO. 2 SIDE RAIL SPACER REAR RH


3. INSTALL SIDE RAIL SPACER REAR LH (for LHD)


4. INSTALL SIDE RAIL SPACER REAR RH (for RHD)


5. INSTALL SIDE RAIL SPACER FRONT LH


6. INSTALL SIDE RAIL SPACER FRONT RH


7. INSTALL ROOF NO. 2 SILENCER PAD


8. INSTALL ROOF HEADLINING ASSEMBLY


B112123E01
  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. Install the roof headlining with the 5 clips.



9. INSTALL ASSIST GRIP
  1. Install the assist grip with the 2 screws.

  1. Close the 2 covers.



10. INSTALL VISOR HOLDER LH


B111747
  1. Attach the 2 claws to install the holder.

  1. Install the screw.



11. INSTALL VISOR HOLDER RH

HINT:
Use the same procedures described for the LH side.



12. INSTALL VISOR ASSEMBLY LH
  1. Install the visor with the screw.



13. INSTALL VISOR ASSEMBLY RH
  1. Install the visor with the screw.



14. INSTALL NO. 1 ROOM LIGHT ASSEMBLY


B085593
  1. Connect the light connector.

  1. Install the room light with the 2 screws.



15. REMOVE NO. 1 ROOM LIGHT LENS


B085012E01
  1. Attach the lens with the 4 claws.



16. INSTALL BACK PANEL TRIM (w/ Back Panel Trim)
  1. Install the back panel trim with the 3 clips.



17. INSTALL QUARTER INSIDE TRIM BOARD LH


    B085571E01
  1. Attach the 3 clips to install the trim board.



    B084915E02
  1. Connect the front seat outer belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the cover.



18. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL QUARTER TRIM PANEL LOWER LH


    B085572E01
  1. Attach the 3 clips and claw to install the trim panel.



    B113104
  1. Install the front seat outer belt's anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



20. INSTALL QUARTER TRIM PANEL LOWER RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL BACK PANEL GARNISH UPPER


B086202E01
  1. Attach the 5 clips and 4 claws to install the garnish.



22. INSTALL FRONT PILLAR GARNISH LH


B111746E01
  1. Attach the 2 clips and 2 claws to install the garnish.

  1. w/ Assist grip:
    Install the assist grip with the 2 screws.

  1. w/ Assist grip:
    Attach the 4 claws to install the 2 assist plugs.



23. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



24. INSTALL COWL SIDE TRIM BOARD LH


B085566E01
  1. Attach the 2 clips to install the trim board.

  1. Install the cap nut.



25. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



26. INSTALL FRONT DOOR OPENING TRIM LH


27. INSTALL FRONT DOOR OPENING TRIM RH


28. INSTALL FRONT DOOR SCUFF PLATE LH


B085559E01
  1. Attach the 4 clips and 8 claws to install the scuff plate.



29. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


31. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.