Home › BODY › INTERIOR › ROOF HEADLINING (for Extra Cab)

ROOF HEADLINING (for Extra Cab) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 3 SIDE RAIL SPACER REAR LH


2. INSTALL NO. 3 SIDE RAIL SPACER REAR RH


3. INSTALL NO. 2 SIDE RAIL SPACER REAR LH


4. INSTALL NO. 2 SIDE RAIL SPACER REAR RH


5. INSTALL SIDE RAIL SPACER REAR LH (for LHD)


6. INSTALL SIDE RAIL SPACER REAR RH (for RHD)


7. INSTALL SIDE RAIL SPACER FRONT LH


8. INSTALL SIDE RAIL SPACER FRONT RH


9. INSTALL NO. 2 ROOF SILENCER PAD


10. INSTALL ROOF HEADLINING ASSEMBLY


B113191E01
  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. Install the roof headlining with the 5 clips.



11. INSTALL ASSIST GRIP
  1. Install the assist grip with the 2 screws.

  1. Close the 2 covers.



12. INSTALL VISOR HOLDER LH


B111747
  1. Attach the 2 claws to install the holder.

  1. Install the screw.



13. INSTALL VISOR HOLDER RH

HINT:
Use the same procedures described for the LH side.



14. INSTALL VISOR ASSEMBLY LH
  1. Install the visor with the screw.



15. INSTALL VISOR ASSEMBLY RH
  1. Install the visor with the screw.



16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY


B085593
  1. Connect the light connector.

  1. Install the room light with the 2 screws.



17. INSTALL NO. 1 ROOM LIGHT LENS


B085012E01
  1. Attach the lens with the 4 claws.



18. INSTALL ROOF SIDE GARNISH INNER UPPER LH


    B085705E01
  1. Attach the 3 clips to install the garnish.



    B087825E02
  1. Connect the rear No. 1 seat belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the cover.



19. INSTALL ROOF SIDE GARNISH INNER UPPER RH

HINT:
Use the same procedures described for the LH side.



20. INSTALL QUARTER PILLAR GARNISH LH


    B084920E04
  1. Connect the front seat outer belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 4 claws to install the seat belt anchor cover cap.



    B085706E01
  1. Attach the 2 clips to install the garnish.



21. INSTALL QUARTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



22. INSTALL QUARTER INSIDE TRIM BOARD LH


    B085707E01
  1. Attach the claws and install the trim pocket to the trim board.

  1. Attach the 7 clips and 6 claws to install the trim board.



    B113105
  1. Connect the front seat outer belt's anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992
  1. Connect the rear No. 1 seat belt's anchor with the built-in bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



23. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



24. INSTALL REAR SEATBACK ASSEMBLY


    B108088E01
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the seatback's 2 hooks to the vehicle body.

  1. Install the seat with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 in.*lbf }



25. INSTALL BACK PANEL GARNISH LOWER


B085704E01
  1. Attach the 5 clips and 6 claws to install the garnish.



26. INSTALL REAR SEAT CUSHION ASSEMBLY LH (w/ Seat Cushion)


    B115404E02
  1. Attach the seat cushion's 2 rear hooks to the vehicle body.



    B115402E01
  1. Attach the seat cushion's front hook to the rear seat cushion lock hook. Then install the seat cushion.

  1. Confirm that the seat cushion is firmly installed.



27. INSTALL REAR SEAT CUSHION ASSEMBLY RH (w/ Seat Cushion)

HINT:
Use the same procedures described for the LH side.



28. INSTALL BACK PANEL GARNISH UPPER


B086202E01
  1. Attach the 5 clips and 4 claws to install the garnish.



29. INSTALL FRONT PILLAR GARNISH LH


B111746E01
  1. Attach the 2 clips and 2 claws to install the garnish.

  1. w/ Assist grip:
    Install the assist grip with the 2 screws.

  1. w/ Assist grip:
    Attach the 4 claws to install the 2 assist plugs.



30. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



31. INSTALL COWL SIDE TRIM BOARD LH


B085566E01
  1. Attach the 2 clips to install the trim board.

  1. Install the cap nut.



32. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



33. INSTALL FRONT DOOR OPENING TRIM LH


34. INSTALL FRONT DOOR OPENING TRIM RH


35. INSTALL FRONT DOOR SCUFF PLATE LH


B085559E01
  1. Attach the 4 clips and 8 claws to install the scuff plate.



36. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



37. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


38. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.