ROOF HEADLINING (for Double Cab) > INSTALLATION |
| 1. INSTALL NO. 3 SIDE RAIL SPACER REAR LH |
| 2. INSTALL NO. 3 SIDE RAIL SPACER REAR RH |
| 3. INSTALL NO. 2 SIDE RAIL SPACER REAR LH |
Install the 2 spacers.
| 4. INSTALL NO. 2 SIDE RAIL SPACER REAR RH |
Install the 2 spacers.
| 5. INSTALL SIDE RAIL SPACER REAR LH |
LHD, w/o Rear roof assist grip:
Install the 2 spacers.
LHD, w/ Rear roof assist grip:
Install the spacer.
RHD, w/o Rear roof assist grip:
Install the spacer.
| 6. INSTALL SIDE RAIL SPACER REAR RH |
LHD, w/o Rear roof assist grip:
Install the spacer.
RHD, w/o Rear roof assist grip:
Install the 2 spacers.
RHD, w/ Rear roof assist grip:
Install the spacer.
| 7. INSTALL SIDE RAIL SPACER FRONT LH |
| 8. INSTALL SIDE RAIL SPACER FRONT RH |
| 9. INSTALL ROOF NO. 2 SILENCER PAD |
Install the 2 silencer pads.
| 10. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Align the wire harness to the markings, and then install the wire harness with tape.
![]() |
w/o Rear roof assist grip:
Install the roof headlining with the 9 clips.
w/ Rear roof assist grip:
Install the roof headlining with the 5 clips.
| 11. INSTALL ASSIST GRIP |
![]() |
w/o Rear roof assist grip:
Install the assist grip with the 2 screws.
w/o Rear roof assist grip:
Close the 2 covers.
w/ Rear roof assist grip:
Install the 3 assist grips with the 6 screws.
w/o Rear roof assist grip:
Close the 6 covers.
| 12. INSTALL VISOR HOLDER LH |
![]() |
Attach the 2 claws to install the holder.
Install the screw.
| 13. INSTALL VISOR HOLDER RH |
| 14. INSTALL VISOR ASSEMBLY LH |
Install the visor with the screw.
| 15. INSTALL VISOR ASSEMBLY RH |
Install the visor with the screw.
| 16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Connect the light connector.
Install the room light with the 2 screws.
| 17. INSTALL NO. 1 ROOM LIGHT LENS |
![]() |
Attach the lens with the 4 claws.
| 18. INSTALL MAP LIGHT ASSEMBLY (w/ Personal Light) |
![]() |
Install the bulb to the light.
Connect the connector.
Attach the map light as shown in the illustration.
Install the 2 screws.
| 19. INSTALL QUARTER INSIDE TRIM BOARD LH |
![]() |
Attach the 4 clips to install the trim board.
![]() |
Connect the rear No. 1 seat belt's shoulder anchor.
Connect the shoulder anchor with the bolt.
Attach the 2 claws to close the cover.
| 20. INSTALL QUARTER INSIDE TRIM BOARD RH |
| 21. INSTALL QUARTER TRIM PANEL LOWER LH |
![]() |
Attach the 3 clips and claw to install the trim panel.
| 22. INSTALL QUARTER TRIM PANEL LOWER RH |
| 23. INSTALL BACK PANEL TRIM (w/ Back Panel Trim) |
Install the back panel trim with the 3 clips.
| 24. INSTALL BACK PANEL GARNISH UPPER |
![]() |
Attach the 5 clips and 4 claws to install the garnish.
| 25. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Attach the 2 clips and 2 claws to install the garnish.
w/ Assist grip:
Install the assist grip with the 2 screws.
w/ Assist grip:
Attach the 4 claws to install the 2 assist plugs.
| 26. INSTALL FRONT PILLAR GARNISH RH |
| 27. INSTALL CENTER PILLAR GARNISH LH |
![]() |
Connect the front seat outer belt's shoulder anchor.
Connect the shoulder anchor with the bolt.
Attach the 4 claws to install the seat belt anchor cover cap.
![]() |
Attach the clip and claw to install the garnish.
| 28. INSTALL CENTER PILLAR GARNISH RH |
| 29. INSTALL CENTER PILLAR GARNISH LOWER LH |
![]() |
Attach the 2 clips and 2 claws to install the garnish.
![]() |
Connect the front seat outer belt's anchor with built-in bolt.
| 30. INSTALL CENTER PILLAR GARNISH LOWER RH |
| 31. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 33. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Attach the 2 clips and 7 claws to install the scuff plate.
| 34. REMOVE REAR DOOR SCUFF PLATE RH |
| 35. INSTALL COWL SIDE TRIM BOARD LH |
![]() |
Attach the 2 clips to install the trim board.
Install the cap nut.
| 36. INSTALL COWL SIDE TRIM BOARD RH |
| 37. INSTALL FRONT DOOR OPENING TRIM LH |
| 38. INSTALL FRONT DOOR OPENING TRIM RH |
| 39. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Attach the 3 clips and 7 claws to install the scuff plate.
| 40. INSTALL FRONT DOOR SCUFF PLATE RH |
| 41. INSTALL REAR SEAT ASSEMBLY |
Install the rear seat (Click here).
| 42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 43. PERFORM INITIALIZATION |
Perform initialization (Click here).