Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW GLASS

BACK WINDOW GLASS > REMOVAL

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here ).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE VISOR ASSEMBLY LH (for Single Cab)
  1. Remove the 2 screws and visor.



3. BLEED VISOR ASSEMBLY RH (for Single Cab)
  1. Remove the 2 screws and visor.



4. REMOVE VISOR HOLDER LH (for Single Cab)


B085570E01
  1. Remove the screw.

  1. Using a screwdriver, detach the 2 claws and remove the holder.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE VISOR HOLDER RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



6. REMOVE FRONT SEAT ASSEMBLY (for Single Cab Bench Seat Type)


    B122861E01
  1. Pull the inner belts out from the bottom of the seat cushion.

  1. Remove the 4 bolts.

  1. w/ Occupant detection sensor:
    Disconnect the connector under the seat.

  1. Remove the seat.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE FRONT SEAT ASSEMBLY (for Single Cab Separate Seat Type)


B108471
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

  1. w/ Seat belt warning, w/ occupant detection sensor and w/ seat heater system:
    Disconnect the connector under the seat.

  1. Remove the seat.

    NOTICE:
    Be careful not to damage the vehicle body.



8. REMOVE BACK PANEL GARNISH UPPER (for Single Cab)


B086202E01
  1. Using a screwdriver, detach the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the garnish.



9. REMOVE FRONT DOOR SCUFF PLATE LH (for Single Cab)


B085559E01
  1. Using a screwdriver, detach the 8 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 4 clips and remove the scuff plate.



10. REMOVE FRONT DOOR SCUFF PLATE RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



11. REMOVE FRONT DOOR OPENING TRIM LH (for Single Cab)


12. REMOVE FRONT DOOR OPENING TRIM RH (for Single Cab)


13. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (for Single Cab)
  1. Remove the front seat outer belt assembly LH .

    HINT:
    For each side, only remove the 2 bolts, floor anchor and shoulder anchor.



14. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (for Single Cab)
  1. Remove the front seat outer belt assembly RH (Click here).

    HINT:
    For each side, only remove the 2 bolts, floor anchor and shoulder anchor.



15. REMOVE QUARTER TRIM PANEL LOWER LH (for Single Cab)


    B113104
  1. Remove the bolt and disconnect the front seat outer belt's anchor.



    B085572E01
  1. Using a screwdriver, detach the claw.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 3 clips and remove the trim panel.



16. REMOVE QUARTER TRIM PANEL LOWER RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



17. REMOVE QUARTER INSIDE TRIM BOARD LH (for Single Cab)


    B086292E05
  1. Disconnect the front seat outer belt's shoulder anchor.

    1. Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Remove the bolt and disconnect the shoulder anchor.



    B085571E01
  1. Using a clip remover, detach the 3 clips and remove the trim board.



18. REMOVE QUARTER INSIDE TRIM BOARD RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



19. REMOVE ASSIST GRIP (for Single Cab)


B085567E01
  1. Using a screwdriver, detach the 4 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 screws and assist grip.



20. REMOVE ROOM LIGHT ASSEMBLY (for Single Cab)


21. REMOVE ROOF HEADLINING ASSEMBLY (for Single Cab)


B113087E01
  1. Using a clip remover, remove the 5 clips and headlining.

  1. Remove the wire harness.



22. REMOVE FRONT DOOR SCUFF PLATE LH (for Extra Cab)


B085559E01
  1. Using a screwdriver, detach the 8 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 4 clips and remove the scuff plate.



23. REMOVE FRONT DOOR SCUFF PLATE RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



24. REMOVE FRONT DOOR OPENING TRIM LH (for Extra Cab)


25. REMOVE FRONT DOOR OPENING TRIM RH (for Extra Cab)


26. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (for Extra Cab)


B086292E02
  1. Single cab:
    Remove the outer belt shoulder anchor.

    1. Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and shoulder anchor.



    B086294E02
  1. Double cab:
    Remove the outer belt shoulder anchor.

    1. Using a screwdriver, disengage the 4 claws and remove the seat belt anchor cover cap.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and shoulder anchor.



    B086379E02
  1. w/o Pretensioner:
    Remove the bolt and seat belt.



    B113099
  1. w/ Pretensioner:

    1. Disconnect the pretensioner connector as shown in the illustration.



    2. B113098E02
    3. Remove the bolt and seat belt.



27. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (for Extra Cab)


28. REMOVE REAR SEAT CUSHION ASSEMBLY LH (for Extra Cab)


    B115401E01
  1. Pull the seat cushion lock hook's release lever in the direction indicated by the arrow in the illustration, and then disconnect the hook on the front of the seat cushion.



    B115729
  1. Detach the seat cushion's 2 rear hooks from the vehicle body.

  1. Remove the seat cushion.



29. REMOVE REAR SEAT CUSHION ASSEMBLY RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



30. REMOVE BACK PANEL GARNISH UPPER (for Extra Cab)


B086046E01
  1. Using a screwdriver, detach the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the garnish.



31. REMOVE BACK PANEL GARNISH LOWER (for Extra Cab)


B085704E01
  1. Using a screwdriver, detach the 6 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the garnish.



32. REMOVE QUARTER INSIDE TRIM BOARD LH (for Extra Cab)


    B113105
  1. Remove the bolt and disconnect the front seat outer belt's anchor.



    B114992
  1. Remove the rear No. 1 seat belt anchor's built-in bolt and disconnect the belt's anchor.



    B085707E01
  1. Using a clip remover, detach the 7 clips.

  1. Using a screwdriver, detach the 6 claws and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the claws and remove the trim pocket from the trim board.



33. REMOVE QUARTER INSIDE TRIM BOARD RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



34. REMOVE ROOF SIDE GARNISH INNER UPPER LH (for Extra Cab)


    B086292E05
  1. Disconnect the rear No. 1 seat belt's shoulder anchor.

    1. Using a screwdriver, detach the 2 claws and open the cover.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and disconnect the shoulder anchor.



    B085705E01
  1. Using a clip remover, detach the 3 clips and remove the garnish.



35. REMOVE ROOF SIDE GARNISH INNER UPPER RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



36. REMOVE QUARTER PILLAR GARNISH LH (for Extra Cab)


    B086294E03
  1. Disconnect the front seat outer belt's shoulder anchor.

    1. Using a screwdriver, detach the 4 claws and remove the seat belt anchor cover cap.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and disconnect the shoulder anchor.



    B085706E01
  1. Using a clip remover, detach the 2 clips and remove the garnish.



37. REMOVE QUARTER PILLAR GARNISH RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



38. REMOVE ROOF HEADLINING ASSEMBLY (for Extra Cab)
  1. Remove the roof headlining assembly .

    HINT:
    It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the back window glass can be removed.



39. REMOVE REAR SEAT HINGE COVER LH (for Double Cab)


B111890E01
  1. Using a screwdriver, detach the 2 claws labeled A.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the hinge cover in the direction indicated by the arrow in the illustration to detach the claw labeled B. Then remove the hinge cover.



40. REMOVE REAR SEAT HINGE COVER RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



41. REMOVE REAR SEAT ASSEMBLY (for Double Cab)


    B115579E01
  1. Remove the fold seat stopper band from the knob and fully extend the band.
    Pull the fold seat stopper band and fold up the seat as shown in the illustration.



    B115580
  1. Pull the inner belts out from between the seat cushion and seatback.



    B084935E01
  1. Remove the 4 bolts.

  1. Lift up the seat in the direction indicated by the arrow in the illustration to detach the 2 hooks from the vehicle body. Then remove the seat.

    NOTICE:
    Be careful not to damage the vehicle body.



42. REMOVE BACK PANEL GARNISH UPPER (for Double Cab)


B086046E01
  1. Using a screwdriver, detach the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the garnish.



43. REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)


B085564E01
  1. Using a screwdriver, detach the 7 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 2 clips and remove the scuff plate.



44. REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



45. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab)


46. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab)


47. REMOVE REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH (for Double Cab)
  1. Remove the rear No. 1 seat belt assembly outer LH .

    HINT:
    For each side, only remove the 2 bolts, floor anchor and shoulder anchor.



48. REMOVE REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH (for Double Cab)
  1. Remove the rear No. 1 seat belt assembly outer (Click here).

    HINT:
    For each side, only remove the 2 bolts, floor anchor and shoulder anchor.



49. REMOVE QUARTER TRIM PANEL LOWER LH (for Double Cab)


B085565E02
  1. Using a screwdriver, detach the claw.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 3 clips and remove the trim panel.



50. REMOVE QUARTER TRIM PANEL LOWER RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



51. REMOVE QUARTER INSIDE TRIM BOARD LH (for Double Cab)


    B086292E05
  1. Disconnect the rear No. 1 seat belt's shoulder anchor.

    1. Using a screwdriver, detach the 2 claws and open the cover.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and disconnect the shoulder anchor.



    B085560E01
  1. Using a clip remover, detach the 4 clips and remove the trim board.



52. REMOVE QUARTER INSIDE TRIM BOARD RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



53. REMOVE ASSIST GRIP (for Double Cab)


B085567E01
  1. w/o Rear roof assist grip:
    Using a screwdriver, detach the 4 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

  1. w/o Rear roof assist grip:
    Remove the 2 screws and assist grip.

  1. w/ Rear roof assist grip:
    Using a screwdriver, detach the 12 claws and open the 6 covers.

    HINT:
    Tape the screwdriver tip before use.

  1. w/ Rear roof assist grip:
    Remove the 6 screws and 3 assist grips.



54. REMOVE ROOF HEADLINING ASSEMBLY (for Double Cab)
  1. Remove the roof headlining assembly .

    HINT:
    It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the back window glass can be removed.



55. REMOVE BACK WINDOW GLASS


B084579E01
  1. w/ Defogger:
    Disconnect the back window defogger connector.

  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

  1. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

  1. Cut through the adhesive by pulling the piano wire around the glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.

  1. Using suction cups remove the glass.



56. CLEAN BACK WINDOW GLASS


B073128
  1. Using a scraper, remove the spacers, moulding and adhesive sticking to the glass.

  1. Clean the outer edges of the glass with non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Even if using new glass, clean it with non-residue solvent.



57. CLEAN VEHICLE BODY


B073084E01
  1. Clean and shape the contact surface of the vehicle body.

    1. Use a knife to cut away excess adhesive on the contact surface of the vehicle body, as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      NOTICE:
      Even if all the adhesive has been removed, clean the vehicle body.