Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW GLASS

BACK WINDOW GLASS > INSTALLATION

for Preparation Click here



1. INSTALL BACK WINDOW GLASS SPACER


B084580E02
  1. Apply Primer G to the glass where the spacers will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Install 2 new stoppers and 2 new spacers onto the glass as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    a
    40.0 mm (1.575 in.)
    b
    16.3 mm (0.642 in.)



    B085122E01
  1. Install 2 new spacers to the vehicle body as shown in the illustration.



2. INSTALL BACK WINDOW MOULDING OUTSIDE UPPER (for Fixed Type)
  1. Apply Primer G to the glass where the moulding and dam will be installed.

    HINT:
    If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.

    3. Do not apply too much primer.


      B123963E01

      Standard measurement:
      Area
      Specified Condition
      a
      6.4 mm (0.252 in.)
      b
      12.7 mm (0.450 in.)
      c
      7.5 mm (0.295 in.)



  1. Remove the peeling paper from the adhesive part of the moulding. Install a new moulding (adhesive side) to the glass (Primer G area) as shown in the illustration.


    B084582E01

    Standard measurement:
    Area
    Specified Condition
    a
    6.4 mm (0.252 in.)



3. INSTALL BACK WINDOW MOULDING OUTSIDE UPPER (for Slide Type)
  1. Apply Primer G to the glass where the moulding and dam will be installed.

    HINT:
    If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.

    3. Do not apply too much primer.


      B118315E01

      Standard measurement:
      Area
      Specified Condition
      a
      6.4 mm (0.252 in.)
      b
      12.7 mm (0.450 in.)
      c
      7.5 mm (0.295 in.)



  1. Remove the peeling paper from the adhesive part of the moulding. Install a new moulding (adhesive side) to the glass (Primer G area) as shown in the illustration.


    B118319E01

    Standard measurement:
    Area
    Specified Condition
    a
    6.4 mm (0.252 in.)



4. INSTALL BACK WINDOW GLASS ADHESIVE DAM (for Fixed Type)


  1. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area) as shown in the illustration.


    B084583E01

    Standard measurement:
    Area
    Specified Condition
    a
    7.5 mm (0.295 in.)



5. INSTALL BACK WINDOW GLASS ADHESIVE DAM (for Slide Type)


  1. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area) as shown in the illustration.


    B123964E01

    Standard measurement:
    Area
    Specified Condition
    a
    7.5 mm (0.295 in.)



6. INSTALL BACK WINDOW GLASS (for Fixed Type)


B084586E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer m to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.


    B084584E01

    HINT:
    If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the glass as shown in the illustration.


      B084585E01

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      12.0 mm (0.472 in.)
      d
      16.6 mm (0.654 in.)
      e
      17.7 mm (0.697 in.)

  1. Install the glass to the vehicle body.

    1. Lightly press the front surface of the glass to ensure that it is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and glass have a small gap between them.

    2. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



7. INSTALL BACK WINDOW GLASS (for Slide Type)


B084586E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer m to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.


    B118317E01

    HINT:
    If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the glass as shown in the illustration.


      B118318E01

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      12.0 mm (0.472 in.)
      d
      16.6 mm (0.654 in.)
      e
      17.7 mm (0.697 in.)

  1. Install the glass to the vehicle body.

    1. Lightly press the front surface of the glass to ensure that it is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and glass have a small gap between them.

    2. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



8. INSTALL ROOF HEADLINING ASSEMBLY (for Single Cab)


B112123E01
  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. Install the roof headlining with the 5 clips.



9. INSTALL ROOM LIGHT ASSEMBLY (for Single Cab)


10. INSTALL ASSIST GRIP (for Single Cab)
  1. Install the assist grip with the 2 screws.

  1. Close the 2 covers.



11. INSTALL QUARTER INSIDE TRIM BOARD LH (for Single Cab)


    B085571E01
  1. Attach the 3 clips to install the trim board.



    B084915E02
  1. Connect the front seat outer belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the cover.



12. INSTALL QUARTER INSIDE TRIM BOARD RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



13. INSTALL QUARTER TRIM PANEL LOWER LH (for Single Cab)


    B085572E01
  1. Attach the 3 clips and claw to install the trim panel.



    B113104
  1. Install the front seat outer belt's anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



14. INSTALL QUARTER TRIM PANEL LOWER RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



15. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (for Single Cab)


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01
  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03
  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993
  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01
  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01
  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01
  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01
  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01
  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



16. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (for Single Cab)


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01
  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03
  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993
  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01
  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01
  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01
  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01
  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01
  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



17. INSTALL FRONT DOOR OPENING TRIM LH (for Single Cab)


18. INSTALL FRONT DOOR OPENING TRIM RH (for Single Cab)


19. INSTALL FRONT DOOR SCUFF PLATE LH (for Single Cab)


B085559E01
  1. Attach the 4 clips and 8 claws to install the scuff plate.



20. INSTALL FRONT DOOR SCUFF PLATE RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



21. INSTALL BACK PANEL GARNISH UPPER (for Single Cab)


B086202E01
  1. Attach the 5 clips and 4 claws to install the garnish.



22. INSTALL FRONT SEAT ASSEMBLY (for Single cab separate seat type)
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. w/ Seat belt warning, w/ occupant detection sensor and w/ seat heater system:
    Connect the connector under the seat.



    B108471E01
  1. Install the seat with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



23. INSTALL FRONT SEAT ASSEMBLY (for Single cab bench seat type)


B122862E01
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. w/ Occupant detection sensor:
    Connect the connector under the seat.

  1. Install the seat with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Pass the inner belts through the hole of the seat cushion.



24. INSTALL VISOR HOLDER LH (for Single Cab)


B111747
  1. Attach the 2 claws to install the holder.

  1. Install the screw.



25. INSTALL VISOR HOLDER RH (for Single Cab)

HINT:
Use the same procedures described for the LH side.



26. INSTALL VISOR ASSEMBLY LH (for Single Cab)
  1. Install the visor with the screw.



27. INSTALL VISOR ASSEMBLY RH (for Single Cab)
  1. Install the visor with the screw.



28. INSTALL ROOF HEADLINING ASSEMBLY (for Extra Cab)


B113191E01
  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. Install the roof headlining with the 5 clips.



29. INSTALL QUARTER PILLAR GARNISH LH (for Extra Cab)


    B084920E04
  1. Connect the front seat outer belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 4 claws to install the seat belt anchor cover cap.



    B085706E01
  1. Attach the 2 clips to install the garnish.



30. INSTALL QUARTER PILLAR GARNISH RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



31. INSTALL ROOF SIDE GARNISH INNER UPPER LH (for Extra Cab)


    B085705E01
  1. Attach the 3 clips to install the garnish.



    B087825E02
  1. Connect the rear No. 1 seat belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the cover.



32. INSTALL ROOF SIDE GARNISH INNER UPPER RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



33. INSTALL QUARTER INSIDE TRIM BOARD LH (for Extra Cab)


    B085707E01
  1. Attach the claws and install the trim pocket to the trim board.

  1. Attach the 7 clips and 6 claws to install the trim board.



    B113105
  1. Connect the front seat outer belt's anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992
  1. Connect the rear No. 1 seat belt's anchor with the built-in bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



34. INSTALL QUARTER INSIDE TRIM BOARD RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



35. INSTALL BACK PANEL GARNISH LOWER (for Extra Cab)


B085704E01
  1. Attach the 5 clips and 6 claws to install the garnish.



36. INSTALL BACK PANEL GARNISH UPPER (for Extra Cab)


B086202E01
  1. Attach the 5 clips and 4 claws to install the garnish.



37. INSTALL REAR SEAT CUSHION ASSEMBLY LH (for Extra Cab)


    B115404E02
  1. Attach the seat cushion's 2 rear hooks to the vehicle body.



    B115402E01
  1. Attach the seat cushion's front hook to the rear seat cushion lock hook. Then install the seat cushion.

  1. Confirm that the seat cushion is firmly installed.



38. INSTALL REAR SEAT CUSHION ASSEMBLY RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



39. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (for Extra Cab)


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01
  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03
  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993
  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01
  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01
  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01
  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01
  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01
  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



40. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (for Extra Cab)


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01
  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03
  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993
  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01
  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01
  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01
  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01
  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01
  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



41. INSTALL FRONT DOOR OPENING TRIM LH (for Extra Cab)


42. INSTALL FRONT DOOR OPENING TRIM RH (for Extra Cab)


43. INSTALL FRONT DOOR SCUFF PLATE RH (for Extra Cab)


B085559E01
  1. Attach the 4 clips and 8 claws to install the scuff plate.



44. INSTALL FRONT DOOR SCUFF PLATE RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



45. INSTALL ROOF HEADLINING ASSEMBLY (for Double Cab)


    B122941E01
  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.



    B122940E01
  1. w/o Rear roof assist grip:
    Install the roof headlining with the 9 clips.

  1. w/ Rear roof assist grip:
    Install the roof headlining with the 5 clips.



46. INSTALL ASSIST GRIP (for Double Cab)


B111748E01
  1. w/o Rear roof assist grip:
    Install the assist grip with the 2 screws.

  1. w/o Rear roof assist grip:
    Close the 2 covers.

  1. w/ Rear roof assist grip:
    Install the 3 assist grips with the 6 screws.

  1. w/o Rear roof assist grip:
    Close the 6 covers.



47. INSTALL QUARTER INSIDE TRIM BOARD RH (for Double Cab)


B085560E01
  1. Attach the 4 clips to install the trim board.



    B087825E02
  1. Connect the rear No. 1 seat belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the cover.



48. INSTALL QUARTER INSIDE TRIM BOARD RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



49. INSTALL QUARTER TRIM PANEL LOWER LH (for Double Cab)


B085565E02
  1. Attach the 3 clips and claw to install the trim panel.



50. INSTALL QUARTER TRIM PANEL LOWER RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



51. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH (for Double Cab)


B113856E02
  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825
  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02
  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01
  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



52. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH (for Double Cab)


B113856E02
  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825
  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02
  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01
  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



53. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab)


54. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab)


55. INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)


B085564E01
  1. Attach the 2 clips and 7 claws to install the scuff plate.



56. INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



57. INSTALL BACK PANEL GARNISH UPPER (for Double Cab)


B086202E01
  1. Attach the 5 clips and 4 claws to install the garnish.



58. INSTALL REAR SEAT ASSEMBLY (for Double Cab)


    B086067E01
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the seatback's 2 hooks to the vehicle body.

  1. Install the seat with the 4 bolts.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



    B115581
  1. Pass the inner belts between the seat cushion and seatback.



    B087757E01
  1. Fold down the seat cushion.

  1. Hook the fold seat stopper band around the knob.



59. INSTALL REAR SEAT HINGE COVER LH (for Double Cab)


    B108083E01
  1. Attach the 3 claws to install the hinge cover.



60. INSTALL REAR SEAT HINGE COVER RH (for Double Cab)

HINT:
Use the same procedures described for the LH side.



61. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



62. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


63. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.