Home › ENGINE ยท 2KD-FTV › LUBRICATION › OIL PUMP (w/o EGR Cooler)

OIL PUMP (w/o EGR Cooler) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



1. REMOVE ENGINE ASSEMBLY
(Click here)


2. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.



    A148169
  1. Remove the 6 bolts and timing belt cover.



3. REMOVE TIMING BELT


    A070549E02
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.



    A070550E01
  1. Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.



  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A148170E01
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.



4. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY


    I034100E02
  1. Disconnect the connector.

  1. Remove the 2 bolts and viscous with magnet clutch heater assembly.



5. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 viscous heater bracket.



6. REMOVE NO. 2 IDLE PULLEY ASSEMBLY


7. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



8. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.



9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.



10. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



11. REMOVE MANIFOLD STAY
  1. Disconnect the 3 vacuum hoses from the 2 VSV.



    A148131
  1. Remove the 2 bolts and stay.



12. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Remove the engine oil level dipstick.



    G036615E01
  1. Remove the bolt and clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring engine oil level dipstick guide.



    A098969E03
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



13. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A098967E05
  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



14. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY


    A098893E01
  1. Remove the 2 bolts.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.



    A231804E01
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    G034844E02
  1. Disconnect the ventilation hose.

  1. Disconnect the 4 injector connectors.



    A060180E01
  1. Using a small screwdriver, remove the 4 nozzle holder seals by prying the portion between each nozzle holder seal and the cutout part of the cylinder head cover.



    G034877E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.



16. REMOVE CAMSHAFT TIMING PULLEY


A060182E01
  1. Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.



17. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


18. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and timing belt cover.



19. REMOVE WATER PUMP ASSEMBLY


A225339
  1. Remove the 5 bolts, 2 nuts, water pump and gasket.



20. REMOVE VACUUM PUMP ASSEMBLY


    A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



21. REMOVE VANE PUMP ASSEMBLY


    A233594
  1. Remove the 2 nuts, vane pump and O-ring.



22. REMOVE PUMP DRIVE SHAFT PULLEY


    A038747E01
  1. Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E03
  1. Using SST, hold the crankshaft pulley and remove the nut and O-ring.

    SST
    09213-58014  
    09330-00021  



23. REMOVE CRANKSHAFT PULLEY


    A072413E02
  1. Using SST, remove the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A072414E02
  1. Using SST, remove the pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



24. REMOVE CAMSHAFT POSITION SENSOR
  1. Remove the bolt and camshaft position sensor.



25. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and crankshaft position sensor.



26. REMOVE TIMING GEAR COVER


    A038748E01
  1. Remove the wire harness clamp.

  1. Remove the 14 bolts and 2 nuts.

  1. Using a slotted screwdriver, gently separate the cover from the timing gear case.

    HINT:
    There are tiny slots that allow you to insert the slotted screwdriver tip for separating the timing gear case and its cover. Refer to the illustration for the slot locations.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing gear case and its cover.

  1. Remove the cover and O-ring.



27. REMOVE NO. 1 IDLE GEAR


    A060161E01
  1. Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.

  1. Remove the 2 bolts and thrust plate.

  1. Remove the service bolt.

  1. Turn the No. 2 idle sub gear and align the gear teeth of the No. 1 idle gear and No. 2 idle sub gear.

  1. Remove the No. 1 idle gear together with the No. 2 idle sub gear.

  1. Remove the idle gear shaft.



28. REMOVE CRANKSHAFT TIMING GEAR


    A060163E01
  1. Remove the No. 1 crankshaft sensor plate.



    A060156E01
  1. Using SST, remove the crankshaft timing gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05010)



29. REMOVE INJECTION GEAR


    A071164E01
  1. Using SST, remove the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



30. REMOVE FUEL SUPPLY PUMP ASSEMBLY


G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.



    A098969E07
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



    A098895E01
  1. Disconnect the 2 fuel hoses.



    A098896E01
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley by using SST.

    SST
    09213-58013  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



31. REMOVE ENGINE OIL LEVEL DIPSTICK


32. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



33. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 22 bolts and 2 nuts.



    Z004119E03
  1. Insert the blade of an oil pan seal cutter between the cylinder block and oil pan. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the timing gear case and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.

  1. Clean off any sealer remaining on the oil pan and cylinder block.



34. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, nut, oil strainer and gasket.



35. REMOVE TIMING GEAR CASE ASSEMBLY
  1. Remove the nut and No. 1 vacuum transmitting pipe.



    A060153E01
  1. Remove the 8 bolts and union bolt. Then remove the timing gear case and 2 O-rings.

    NOTICE:
    Do not drop the oil pump rotor.

  1. Remove the gasket.