POWER WINDOW MASTER SWITCH > ON-VEHICLE INSPECTION |
| 1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Single cab, Extra cab) |
![]() |
for LHD:
Measure the resistance of the power window switch.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (U) - 1 (E) | Ignition switch ON, driver side power window switch OFF → UP (manual operation) | Below 1 V → 10 to 14 V |
| 4 (D) - 1 (E) | Ignition switch ON, driver side power window switch OFF → DOWN (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open | Below 1 V → 10 to 14 V → Below 1 V |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 1 (E) - 10 (D) 9 (B) - 8 (U) | Below 1 Ω |
| OFF | OFF | 1 (E) - 8 (U) 1 (E) - 10 (D) | Below 1 Ω |
| OFF | DOWN | 1 (E) - 8 (U) 9 (B) - 10 (D) | Below 1 Ω |
| ON | UP | 1 (E) - 10 (D) | 10 kΩ or higher |
| 9 (B) - 8 (U) | Below 1 Ω | ||
| ON | OFF | 8 (U) - 10 (D) | Below 1 Ω |
| ON | DOWN | 1 (E) - 8 (U) | 10 kΩ or higher |
| 9 (B) - 10 (D) | Below 1 Ω |
![]() |
Apply battery voltage to the master switch and check that the AUTO light illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 9 (B) Battery negative (-) → Terminal 1 (E) | AUTO light illuminates |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (E) - 2 (L) | Lock | Below 1 Ω |
| 1 (E) - 2 (L) 1 (E) - 5 (UL) | OFF | 10 kΩ or higher |
| 1 (E) - 5 (UL) | Unlock | Below 1 Ω |
![]() |
for RHD:
Measure the resistance of the power window switch.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (U) - 10 (E) | Ignition switch ON, driver side power window switch OFF → UP (manual operation) | Below 1 V → 10 to 14 V |
| 5 (D) - 10 (E) | Ignition switch ON, driver side power window switch OFF → DOWN (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open | Below 1 V → 10 to 14 V → Below 1 V |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 10 (E) - 1 (D) 9 (B) - 8 (U) | Below 1 Ω |
| OFF | OFF | 10 (E) - 8 (U) 10 (E) - 1 (D) | Below 1 Ω |
| OFF | DOWN | 10 (E) - 8 (U) 9 (B) - 1 (D) | Below 1 Ω |
| ON | UP | 10 (E) - 1 (D) | 10 kΩ or higher |
| 9 (B) - 8 (U) | Below 1 Ω | ||
| ON | OFF | 8 (U) - 1 (D) | Below 1 Ω |
| ON | DOWN | 10 (E) - 8 (U) | 10 kΩ or higher |
| 9 (B) - 1 (D) | Below 1 Ω |
![]() |
Apply battery voltage to the master switch and check that the AUTO light illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 9 (B) Battery negative (-) → Terminal 10 (E) | AUTO light illuminates |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 10 (E) - 3(L) | Lock | Below 1 Ω |
| 10 (E) - 4(L) 10 (E) - 4(UL) | OFF | 10 kΩ or higher |
| 10 (E) - 4(UL) | Unlock | Below 1 Ω |
| 2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double cab) |
for LHD:

Measure the resistance of the power window switch.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (U) - 3 (E) | Ignition switch ON, driver side power window switch OFF → UP (manual operation) | Below 1 V → 10 to 14 V |
| 9 (D) - 3 (E) | Ignition switch ON, driver side power window switch OFF → DOWN (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open | Below 1 V → 10 to 14 V → Below 1 V |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 3 (E) - 15 (D) 6 (B) - 18 (U) | Below 1 Ω |
| OFF | OFF | 3 (E) - 18 (U) 3 (E) - 15 (D) | Below 1 Ω |
| OFF | DOWN | 3 (E) - 18 (U) 6 (B) - 15 (D) | Below 1 Ω |
| ON | UP | 3 (E) - 15 (D) | 10 kΩ or higher |
| 6 (B) - 18 (U) | Below 1 Ω | ||
| ON | OFF | 18 (U) - 15 (D) | Below 1 Ω |
| ON | DOWN | 3 (E) - 18 (U) | 10 kΩ or higher |
| 6 (B) - 15 (D) | Below 1 Ω |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 3 (E) - 13 (D) 6 (B) - 12 (U) | Below 1 Ω |
| OFF | OFF | 3 (E) - 12 (U) 3 (E) - 13 (D) | Below 1 Ω |
| OFF | DOWN | 3 (E) - 12 (U) 6 (B) - 13 (D) | Below 1 Ω |
| ON | UP | 3 (E) - 13 (D) | 10 kΩ or higher |
| 6 (B) - 12 (U) | Below 1 Ω | ||
| ON | OFF | 12 (U) - 13 (D) | Below 1 Ω |
| ON | DOWN | 3 (E) - 12 (U) | 10 kΩ or higher |
| 6 (B) - 13 (D) | Below 1 Ω |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 3 (E) - 16 (D) 6 (B) - 10 (U) | Below 1 Ω |
| OFF | OFF | 3 (E) - 10 (U) 3 (E) - 16 (D) | Below 1 Ω |
| OFF | DOWN | 3 (E) - 10 (U) 6 (B) - 16 (D) | Below 1 Ω |
| ON | UP | 3 (E) - 16 (D) | 10 kΩ or higher |
| 6 (B) - 10 (U) | Below 1 Ω | ||
| ON | OFF | 10 (U) - 16 (D) | Below 1 Ω |
| ON | DOWN | 3 (E) - 10 (U) | 10 kΩ or higher |
| 6 (B) - 16 (D) | Below 1 Ω |
![]() |
Apply battery voltage to the master switch and check that the AUTO light illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 6 (B) Battery negative (-) → Terminal 3 (E) | AUTO light illuminates |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (E) - 5 (L) | Lock | Below 1 Ω |
| 3 (E) - 5 (L) 3 (E) - 8 (UL) | OFF | 10 kΩ or higher |
| 3 (E) - 8 (UL) | Unlock | Below 1 Ω |
for RHD:

Measure the resistance of the power window switch.
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| Always (ON / OFF) | UP | 3 (E) - 9 (D) 4 (U) - 6 (B) | Below 1 Ω |
| Always (ON / OFF) | OFF | 3 (E) - 4 (U) 3 (E) - 9 (D) | Below 1 Ω |
| Always (ON / OFF) | DOWN | 3 (E) - 4 (U) 6 (B) - 9 (D) | Below 1 Ω |
| Always (ON / OFF) | AUTO DOWN | 3 (E) - 4 (U) 6 (B) - 9 (D) | Below 1 Ω |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 3 (E) - 13 (D) 6 (B) - 10 (U) | Below 1 Ω |
| OFF | OFF | 3 (E) - 10 (U) 3 (E) - 13 (D) | Below 1 Ω |
| OFF | DOWN | 3 (E) - 10 (U) 6 (B) - 13 (D) | Below 1 Ω |
| ON | UP | 3 (E) - 13 (D) | 10 kΩ or higher |
| 6 (B) - 10 (U) | Below 1 Ω | ||
| ON | OFF | 10 (U) - 13 (D) | Below 1 Ω |
| ON | DOWN | 3 (E) - 10 (U) | 10 kΩ or higher |
| 6 (B) - 13 (D) | Below 1 Ω |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 3 (E) - 15 (D) 6 (B) - 16 (U) | Below 1 Ω |
| OFF | OFF | 3 (E) - 16 (U) 3 (E) - 15 (D) | Below 1 Ω |
| OFF | DOWN | 3 (E) - 16 (U) 6 (B) - 15 (D) | Below 1 Ω |
| ON | UP | 3 (E) - 15 (D) | 10 kΩ or higher |
| 6 (B) - 16 (U) | Below 1 Ω | ||
| ON | OFF | 16 (U) - 15 (D) | Below 1 Ω |
| ON | DOWN | 3 (E) - 16 (U) | 10 kΩ or higher |
| 6 (B) - 15 (D) | Below 1 Ω |
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 3 (E) - 12 (D) 6 (B) - 18 (U) | Below 1 Ω |
| OFF | OFF | 3 (E) - 18 (U) 3 (E) - 12 (D) | Below 1 Ω |
| OFF | DOWN | 3 (E) - 18 (U) 6 (B) - 12 (D) | Below 1 Ω |
| ON | UP | 3 (E) - 12 (D) | 10 kΩ or higher |
| 6 (B) - 18 (U) | Below 1 Ω | ||
| ON | OFF | 18 (U) - 12 (D) | Below 1 Ω |
| ON | DOWN | 3 (E) - 18 (U) | 10 kΩ or higher |
| 6 (B) - 12 (D) | Below 1 Ω |
![]() |
Apply battery voltage to the master switch and check that the AUTO light illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 6 (B) Battery negative (-) → Terminal 3 (E) | AUTO light illuminates |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (E) - 5 (L) | Lock | Below 1 Ω |
| 3 (E) - 5 (L) 3 (E) - 8 (UL) | OFF | 10 kΩ or higher |
| 3 (E) - 8 (UL) | Unlock | Below 1 Ω |
| 3. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Jam Protection) |

for LHD
Measure the voltage of the power window regulator master switch connector.
| Tester Connection | Condition | Specified Condition |
| 4 (U) - 1 (E) | Ignition switch ON, driver side power window switch OFF → UP (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed | Below 1 V → 10 to 14 V → Below 1 V | |
| 9 (D) - 1 (E) | Ignition switch ON, driver side power window switch OFF → DOWN (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open | Below 1 V → 10 to 14 V → Below 1 V |
| Tester Connection | Condition | Specified Condition |
| 13 (U) - 1 (E) |
| Below 1 V → 10 to 14 V |
| 15 (D) - 1 (E) |
| Below 1 V → 10 to 14 V |
| Tester Connection | Condition | Specified Condition |
| 12 (U) - 1 (E) |
| Below 1 V → 10 to 14 V |
| 10 (D) - 1 (E) |
| Below 1 V → 10 to 14 V |
| Tester Connection | Condition | Specified Condition |
| 18 (U) - 1 (E) |
| Below 1 V → 10 to 14 V |
| 16 (D) - 1 (E) |
| Below 1 V → 10 to 14 V |
![]() |
Apply battery voltage to the master switch and check that the AUTO light illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 6 (B) Battery negative (-) → Terminal 1 (E) | AUTO light illuminates |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (E) - 5 (L) | Lock | Below 1 Ω |
| 3 (E) - 5 (L) 3 (E) - 8 (UL) | OFF | 10 kΩ or higher |
| 3 (E) - 8 (UL) | Unlock | Below 1 Ω |
for RHD

Measure the voltage of the power window regulator master switch connector.
| Tester Connection | Condition | Specified Condition |
| 4 (U) - 1 (E) | Ignition switch ON, driver side power window switch OFF → UP (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed | Below 1 V → 10 to 14 V → Below 1 V | |
| 9 (D) - 1 (E) | Ignition switch ON, driver side power window switch OFF → DOWN (manual operation) | Below 1 V → 10 to 14 V |
| Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open | Below 1 V → 10 to 14 V → Below 1 V |
| Tester Connection | Condition | Specified Condition |
| 13 (U) - 1 (E) |
| Below 1 V → 10 to 14 V |
| 15 (D) - 1 (E) |
| Below 1 V → 10 to 14 V |
| Tester Connection | Condition | Specified Condition |
| 12 (U) - 1 (E) |
| Below 1 V → 10 to 14 V |
| 10 (D) - 1 (E) |
| Below 1 V → 10 to 14 V |
| Tester Connection | Condition | Specified Condition |
| 18 (U) - 1 (E) |
| Below 1 V → 10 to 14 V |
| 16 (D) - 1 (E) |
| Below 1 V → 10 to 14 V |
![]() |
Apply battery voltage to the master switch and check that the AUTO light illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 6 (B) Battery negative (-) → Terminal 1 (E) | AUTO light illuminates |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (E) - 5 (L) | Lock | Below 1 Ω |
| 3 (E) - 5 (L) 3 (E) - 8 (UL) | OFF | 10 kΩ or higher |
| 3 (E) - 8 (UL) | Unlock | Below 1 Ω |