Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Each ECU terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECU terminals.


ECM

G034261E03


Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
NSW (E5-6) - E1 (E7-7)
L-Y - BR
Park/Neutral position switch signal
Ignition switch ON and shift lever on P or N
Below 3 V
NSW (E5-6) - E1 (E7-7)
L-Y - BR
Park/Neutral position switch signal
Ignition switch ON and shift lever not on P or N
9 to 14 V
STA (E5-7) - E1 (E7-7)
B-Y - BR
Starter signal
Ignition switch ON and shift lever on P or N
Below 3 V
STA (E5-7) - E1 (E7-7)
B-Y - BR
Starter signal
Ignition switch ON and shift lever not on P or N
9 to 14 V
STP (E6-15) - E1 (E7-7)
G-W - BR
Stop light switch signal
Brake pedal is depressed
7.5 to 14 V
STP (E6-15) - E1 (E7-7)
G-W - BR
Stop light switch signal
Brake pedal is released
Below 1.5 V
CAN+ (E6-22) - E1 (E7-7)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 6)
CAN- (E6-21) - E1 (E7-7)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 7)

TCM

F043241E01


Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
NSW (T19-12) - E1 (T19-1)
L-Y - BR
Park/Neutral position switch signal
Ignition switch ON and shift lever on P or N
Below 3 V
NSW (T19-12) - E1 (T19-1)
L-Y - BR
Park/Neutral position switch signal
Ignition switch ON and shift lever not on P or N
9 to 14 V
STA (T19-11) - E1 (T19-1)
B-Y - BR
Starter signal
Cranking
6 V or more
R (T18-9) - E1 (T19-1)
R-Y - BR
R shift position switch signal
Ignition switch ON and transfer shift lever on R
7.5 to 14 V
R (T18-9) - E1 (T19-1)
R-Y - BR
R shift position switch signal
Ignition switch ON and transfer shift lever not on R
Below 1.5 V
D (T18-8) - E1 (T19-1)
G-Y - BR
D shift position switch signal
Ignition switch ON and transfer shift lever on D or 3
7.5 to 14 V
D (T18-8) - E1 (T19-1)
G-Y - BR
D shift position switch signal
Ignition switch ON and transfer shift lever not on D or 3
Below 1.5 V
3 (T18-12) - E1 (T19-1)
G-O - BR
3 shift position switch signal
Ignition switch ON and transfer shift lever on 3
7.5 to 14 V
3 (T18-12) - E1 (T19-1)
G-O - BR
3 shift position switch signal
Ignition switch ON and transfer shift lever not on 3
Below 1.5 V
2 (T18-11) - E1 (T19-1)
L - BR
2 shift position switch signal
Ignition switch ON and transfer shift lever on 2
7.5 to 14 V
2 (T18-11) - E1 (T19-1)
L - BR
2 shift position switch signal
Ignition switch ON and transfer shift lever not on 2
Below 1.5 V
L (T18-10) - E1 (T19-1)
G-R - BR
L shift position switch signal
Ignition switch ON and transfer shift lever on L
7.5 to 14 V
L (T18-10) - E1 (T19-1)
G-R - BR
L shift position switch signal
Ignition switch ON and transfer shift lever not on L
Below 1.5 V
S1 (T19-18) - E1 (T19-1)
GR - BR
S1 solenoid signal
Ignition switch ON
9 to 14 V
S1 (T19-18) - E1 (T19-1)
GR - BR
S1 solenoid signal
1st or 2nd gear
9 to 14 V
S1 (T19-18) - E1 (T19-1)
GR - BR
S1 solenoid signal
3rd or O/D gear
Below 1.5 V
S2 (T19-17) - E1 (T19-1)
W-L - BR
S2 solenoid signal
Ignition switch ON
Below 1.5 V
S2 (T19-17) - E1 (T19-1)
W-L - BR
S2 solenoid signal
2nd or 3rd gear
9 to 14 V
S2 (T19-17) - E1 (T19-1)
W-L - BR
S2 solenoid signal
1st or O/D gear
Below 1.5 V
SL (T19-16) - E1 (T19-1)
G - BR
SL solenoid signal
Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)
Pulse generation
(see waveform 1)
SL (T19-16) - E1 (T19-1)
G - BR
SL solenoid signal
Vehicle driving under lock-up condition
9 to 14 V
SLT+ (T19-20) - SLT- (T19-19)
G-Y - L-B
SLT solenoid signal
Ignition switch ON
Below 3 V
SLT+ (T19-20) - SLT- (T19-19)
G-Y - L-B
SLT solenoid signal
Engine idle speed
Pulse generation
(see waveform 2)
THOC (T19-24) - E2 (T19-23)
BR - B-Y
ATF temperature sensor signal
ATF temperature: 115°C (239°F) or more
Below 1.5 V
STP (T17-14) - E1 (T19-1)
G-W - BR
Stop light switch signal
Ignition switch ON and brake pedal is depressed
7.5 to 14 V
STP (T17-14) - E1 (T19-1)
G-W - BR
Stop light switch signal
Ignition switch ON and brake pedal is released
Below 1.5 V
SP1 (T17-25) - E1 (T19-1)
V-R - BR
Speed signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(see waveform 3)
NC0+ (T19-3) - NC0- (T19-2)
V - P
O/D direct clutch speed sensor (NC0) signal
Engine is idling
Pulse generation
(see waveform 4)
SP2+ (T19-30) - SP2- (T19-29)
R - G
No. 2 vehicle speed sensor (SP2) signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(see waveform 5)
SIL (T18-23) - E1 (T19-1)
R-Y - BR
Terminal SIL of DLC3
Connect intelligent tester to DLC3
Pulse generation
WFSE (T18-24) - E1 (T19-1)
W - BR
Terminal SIL of DLC3
Ignition switch ON
9 to 14 V
IG2 (T17-6) - E1 (T19-1)
B-O - BR
Ignition switch
Ignition switch ON
9 to 14 V
CAN+ (T17-21) - E1 (T19-1)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 6)
CAN- (T17-20) - E1 (T19-1)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 7)

Waveform 1 (Reference)
G034875E01
Item
Content
Symbols (Terminal No.)
SL (T19-16) - E1 (T19-1)
Tool Setting
10 V/DIV., 100 msec./DIV.
Condition
Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)

Waveform 2 (Reference)
G023426E03
Item
Content
Symbols (Terminal No.)
SLT+ (T19-20) - SLT- (T19-19)
Tool Setting
5 V/DIV., 1 msec./DIV.
Condition
Engine idle speed

Waveform 3 (Reference)
G034872E01
Item
Content
Symbols (Terminal No.)
SP1 (T17-25) - E1 (T19-1)
Tool Setting
5 V/DIV., 20 msec./DIV.
Condition
Vehicle speed 20 km/h (12 mph)

Waveform 4 (Reference)
G034873E02
Item
Content
Symbols (Terminal No.)
NC0+ (T19-3) - NC0- (T19-2)
Tool Setting
5 V/DIV., 0.5 msec./DIV.
Condition
Engine is idling (P or N position)

Waveform 5 (Reference)
G020664E03
Item
Content
Symbols (Terminal No.)
SP2+ (T19-30) - SP2- (T19-29)
Tool Setting
2 V/DIV., 2 msec./DIV.
Condition
Vehicle speed 20 km/h (12 mph)

Waveform 6 (Reference)
G036660E05
Item
Content
Symbols (Terminal No.)
CAN+ (T17-21) - E1 (T19-1)
Tool Setting
1 V/DIV., 10 msec./DIV.
Condition
Ignition switch ON

Waveform 7 (Reference)
G036661E04
Item
Content
Symbols (Terminal No.)
CAN- (T17-20) - E1 (T19-1)
Tool Setting
1 V/DIV., 10 msec./DIV.
Condition
Ignition switch ON